Model & mdash; The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.Chloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, soil sea breeze, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, the container leaks due to corrosion days after it is replaced with stainless steel.Welland,The application range is wider than that of ferritic stainless steel. Compared with ferritic stainless steel, duplex stainless steel has the following disadvantages: high alloy element content and relatively high price. Generally, ferritic stainless steel does not contain nickel.The experimental ice load of concrete decorated stainless steel pipe is the highest in the cold areaAzua-de-Compostela,The back is blocked with blocking plate for ventilation protection; Only soluble paper or the combination of soluble paper and blocking plate is used for blocking ventilation protection; Use flux cored wire for backing TIG welding.Model & mdash; After that, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it, it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade.Meet the needs of architects and structural designers.

Add a small amount of sulfur and phosphorus to make it easier to cut.Corrosion resistance most stainless steel products require good corrosion resistance. Stainless steel pipe is similar to class I and II tableware, kitchen, water heater, water dispenser, etc. Some foreign businessmen also test the corrosion resistance of products: use NaCl aqueous solution to warm to boiling. After a period of time, the solution is to drain, wash and dry, and determine the weight loss to determine the degree of corrosion.With the implementation of China's reform and opening up, the national economy has achieved rapid growth, public buildings and tourism facilities have been built which puts forward new requirements for hot water supply and domestic water supply. In particular, people pay more and more attention to the problem of water quality, and the requirements are also increasing. Galvanized steel pipe, a common pipe will gradually withdraw from the historical stage under the influence of relevant countries because of its corrosivity. Plastic pipe, composite pipe and copper pipe have become common pipes in the pipeline system. However, under certain circumstances, stainless steel pipe has more advantages, hot water system and water supply system that puts safety and sanitation first, it has the characteristics of safety, reliability, sanitation environmental protection, economy and applicability. It has been proved by engineering practice at home and abroad that it is one of the new, energy-saving and environmental protection pipes with good comprehensive performance of water supply system. It is also a very competitive water supply pipe, which will play an incomparable role in improving water quality and people's living standards.quality standard,Accounting for about % - % of the total steel, it is widely used in the national economy. Because the steel pipe has a hollow section, it is suitable for gas and solid transmission pipelines; at the same time, compared with the round steel of the same weight, the steel pipe has large section coefficient and high flexural and torsional strength, stainless steel pipe itself is an economic section steel that saves metal. It is an important part of steel, especially in oil drilling,WellandStainless steel strip bright annealing furnace, production and metallurgyStainless steel why corrosion-resistant stainless steel decorative pipe, stainless steel pipe, all metals react with oxygen in the atmosphere to form an oxide film on the surface. Unfortunately, the iron oxide formed on ordinary carbon steel continues to oxidize, expanding the corrosion and finally forming holes. The carbon steel surface can be guaranteed by electroplating with paint or oxidation resistant metals (e.g. zinc, nickel and chromium), but as is known, this protection is only a thin film. If the protective layer is, the steel below begins to rust.The bearing capacity of decorative stainless steel pipe ice load is the main control load of offshore platform in severe cold area, which has high requirements for the shear bearing capacity of jacket leg of offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. A compound forming process of double-layer stainless steel pipe for primary circuit main pipeline of station is designed, which solves the problem of limited length of finished products in traditional forging or casting process, and meets the special requirements of complex working environment on pipeline performance. The three roll cross rolling forming process of double-layer casing with outer layer -n austenitic heat-resistant stainless steel and inner layer cr-ni martensitic heat-resistant stainless steel was simulated and optimized by using DEFORM-D finite element simulation software. The internal and external deformation, stress-strain field and temperature field of double-layer stainless steel pipe were analyzed, and the optimal deformation parameter combination was obtained by orthogonal test. The simulation results show that in the process of three roll cross rolling, the large values of equivalent stress, equivalent strain and temperature are concentrated in the area between the outer tube and the roll and the overall performance parameters of the outer tube are greater than those of the inner tube. The range analysis and variance analysis of orthogonal design test show that the optimal deformation parameter is rough rolling temperature deg; C. Feed angle & deg;, Roll speed: rmin. Objective to improve the existing connection mode of the braking system pipe system of railway freight cars, and accurately shape the end of the stainless steel pipe, so as to obtain the forged joint with better mechanical properties. According to the connection mode of the original pipe system and the plastic forming characteristics of steel pipe, a multi-step upsetting and extrusion process for the end of stainless steel pipe is proposed. The process is numerically simulated by DEFORM-D three-dimensional finite element simulation software, and the forging forming process is analyzed

Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.High quality brand, & mdash; high strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It is one of the hard stainless steels. A common application example is & ldquo; shaving blade & rdquo;. There are three common models: C and f (easy processing type).Hot rolled silicon steel sheet hot rolled silicon steel sheet is represented by Dr, which is divided into low silicon steel (silicon content & le; %) and high silicon steel (silicon content & amp; gt; %).Stainless steel, precipitation hardening stainless steel and high alloy with iron content less than % are usually named by patent name or trademark.Welland,Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni%, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%,WellandStainless steel pipe 304 manufacturer,WellandStainless steel pipe industry, and the single-phase austenite structure is obtained by the combination of Cr and Ni.The main way to prevent stress corrosion of austenitic stainless steel is to add SI ~ % and keep the content of N below .% from smelting. In addition, the content of impurities such as P, Sb, Bi and as should be reduced as much as possible. In addition, A-F dual phase steel can be selected, which does not correspond to stress corrosion in Cl - and oh - media. The initial micro crack will not continue to expand after encountering ferrite phase, and the ferrite content should be about % .;- Ferromagnetism due to m transformation shall be considered in use (such as in instrument parts).