Chloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, sea water, sea breeze, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough the container leaks due to corrosion days after it is replaced with stainless steel.When hoisting stainless steel pipes, public slings, such as hoisting belt and public collet number, shall be used. It is strictly prohibited to use steel wire rope to avoid scratching the surface; and when hoisting and placing, it shall prevent scratching caused by impact and collision. If there are surface scratches, electric arc traces and surface purification in the process of transportation, storage and processing, it must be completely cleaned, polished with an angle grinder, and then polished Polishing with optical sheet or metallographic sandpaper.Saint-Albert,The external anti-corrosion coating of stainless steel shall be galvanized and epoxy asphalt coating or coating with higher requirements according to the soil conditions of the pipe laying ground.Stainless steel tube for boiler tube and heat exchanger (gjb- (yb-) aviation structural tube, thick wall seamless steel tube (gjb- (yb-) aviation stainless steel tube (ybt-) (yb-) aviation a blind rivet seamless steel tube (gjb- (yb-) aviation structural tube, seamless steel tube (ybt- (yb- aviation conduit A seamless steel pipe small diameter stainless steel pipe seamless steel pipe for high pressure boiler low and medium pressure boiler pipe stainless acid resistant extremely seamless steel pipe seamless steel pipe for petroleum cracking seamless steel boiler and heat exchanger Ferritic and austenitic alloy pipe general purpose austenitic stainless steel pipe and welded pipe austenitic stainless steel seamless steel pipe welded steel pipe welded steel pipe carbon steel Ferritic and austenitic alloy steel pipe) General requirements General requirements for ferrous and alloy steels for special purposes General requirements for carbonEch Chettia,There shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage, the storage position shall be convenient for lifting and absolutely isolated from other data storage areas. Protective measures shall be taken to avoid purification, collision with other components, purification and damage of iron metal.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.. Raw material problem of stainless steel pipe. If the hardness is too low, it is not easy to polish (BQ is not good). If the hardness is too low, orange peel is easy to appear on the surface during deep drawing, which affects BQ performance. BQ with high hardness is relatively good.

When hoisting stainless steel pipes, public slings, such as hoisting belt and public collet number, shall be used. It is strictly prohibited to use steel wire rope to avoid scratching the surface; and when hoisting and placing, it shall prevent scratching caused by impact and collision. If there are surface scratches, storage and processing, it must be completely cleaned, polished with an angle grinder, and then polished Polishing with optical sheet or metallographic sandpaper.The external anti-corrosion coating of stainless steel shall be galvanized and epoxy asphalt coating or coating with higher requirements according to the soil conditions of the pipe laying ground.The bearing capacity of decorative stainless steel pipe ice load is the main control load of offshore platform in severe cold area, which has high requirements for the shear bearing capacity of jacket leg of offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength,Saint-AlbertStainless steel tape magnetic, the bearing capacity of specimens increases, which solves the problem of limited length of finished products in traditional forging or casting process the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. A compound forming process of double-layer stainless steel pipe for primary circuit main pipeline of station is designed, and meets the special requirements of complex working environment on pipeline performance. The three roll cross rolling forming process of double-layer casing with outer layer -n austenitic heat-resistant stainless steel and inner layer cr-ni martensitic heat-resistant stainless steel was simulated and optimized by using DEFORM-D finite element simulation software. The internal and external deformation, and the optimal deformation parameter combination was obtained by orthogonal test. The simulation results show that in the process of three roll cross rolling, the large values of equivalent stress, equivalent strain and temperature are concentrated in the area between the outer tube and the roll, and the overall performance parameters of the outer tube are greater than those of the inner tube. The range analysis and variance analysis of orthogonal design test show that the optimal deformation parameter is rough rolling temperature deg; C. Feed angle & deg;, Roll speed: rmin. Objective to improve the existing connection mode of the braking system pipe system of railway freight cars, and accurately shape the end of the stainless steel pipe, a multi-step upsetting and extrusion process for the end of stainless steel pipe is proposed. The process is numerically simulated by DEFORM-D three-dimensional finite element simulation software, and the forging forming process is analyzedProject scope,Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.When improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, Nb LC) and susl have been applied to frozen shells. Ferritic stainless steel has body centered cubic structure. When the material properties become weaker, sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.Argon shall conform to the rules of national specifications, and argon with purity of % shall be selected. If the content of impurities is too high, the maintenance effect of argon will be weakened and the weld quality will be indirectly affected.

AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, ocrnimoti, etc. Duplex stainless steel has good weldability no heat treatment is required after welding, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.assetsDesign and research of high precision stainless steel pipe stainless steel pipe has many advantages, such as high strength, good corrosion resistance, strong impact resistance and so on, which makes it widely used in various fields of life. With the continuous improvement of automation, people have higher and higher requirements for the cutting quality of stainless steel pipe. At present, there are still many deficiencies in pipe cutting in China, which seriously restricts China's industrial development. Therefore, recently, the research on pipe cutting machine with high precision, high automation, high cutting quality and high cutting efficiency has become the research focus and difficulty of relevant disciplines, the intermittent cutting method of planetary bisymmetric eccentric installation can reduce the cutting deformation of stainless steel pipe and improve the cutting accuracy; Secondly, the tool of the intermittent stainless steel pipe cutting machine is eccentrically installed on the planetary gear to complete the rotation at the same time of revolution. Therefore, only one main motor can drive two tools to rotate. The mechanical structure reduces the use of the motor, improves the use efficiency of the motor and reduces the manufacturing cost of the equipment; Then, the main components of the intermittent pipe cutter are analyzed by using SolidWorks D solid software and ANSYS finite element analysis software. ANSYS software verifies the rationality of the structure and improves the service life of the pipe cutter. At present, there are still many deficiencies in pipe cutting in China, which seriously restricts China's industrial development. Therefore, recently, the research on pipe cutting machine with high precision, high automation, high cutting quality and high cutting efficiency has become the research focus and difficulty of relevant disciplines, and it is also the inevitable trend of the further development of China's industry. Firstly, the cutting characteristics of the intermittent stainless steel pipe cutter in the cutting process are analyzed, and the cutting force in the cutting process is calculated. Secondly, the overall cutting scheme of the intermittent stainless steel pipe cutter is determined, and the structure is designed. Then, The reliability of its strength and stiffness is verified. In the design process of intermittent stainless steel pipe cutting machine, the combination of theoretical analysis and computer simulation is used to verify the feasibility of the design, complete the tasks of scheme determination, theoretical analysis and structural design, and verify the rationality of the structure. This paper aims to design a pipe cutting machine with high automation, compact structure and high cutting precision, so as to improve the cutting quality of stainless steel pipe and bring more economic and social benefits to the enterprise. This paper comprehensively analyzes the research on stainless steel pipe cutting machines at home and abroad, draws lessons from the advanced structural design of relevant foreign pipe cutting machines,Saint-AlbertStainless steel thin wall water pipe, and makes a comparative analysis and Research on the characteristics of easy deformation and difficult cutting of stainless steel pipes. Taking the stainless steel pipe with diameter of mm ~ mm and wall thickness of mm ~ mm as the design object, and based on the structure of the existing planetary pipe cutting machine, A planetary double symmetrical eccentric installation intermittent cutting is proposed. The cutting can not only realize its own main motion and feed motion, but also reduce the deformation of stainless steel pipe in the cutting process. Professional L stainless steel pipe s stainless steel pipe and L stainless steel pipe have large quantity, excellent quality and low price, fire resistance water resistance, high temperature resistance, strong and durable, safe and reliable, and improve the quality of cutting surface. cold rolled oriented silicon steel strip (sheet) represents: times of DQ + iron loss value (at the frequency of Hz, the magnetic induction peak with sinusoidal waveform is the unit weight iron loss value of T) + times of thickness value. Sometimes G is added after the iron loss value to indicate high magnetic induction. For example, dq represents cold-rolled oriented silicon steel strip (sheet) with iron loss value of and thickness of .mm. Now the new model is q.AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices various specifications of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, CrNiTi, ocrnimoti, etc. Duplex stainless steel has good weldability, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.Saint-Albert,Production process of stainless steel pipe A. preparation of round steel; b. Heating; c. Hot rolling perforation; d. Cutting head; e. Pickling; f. Grinding; g．； h. Cold rolling; i. Degreasing; j. Solution heat treatment; k. Straightening; l. Pipe cutting; m. Pickling; n. Finished product inspection.In the building water supply pipe system, due to the end of the glorious history of galvanized steel pipe, various new plastic pipes and composite pipes have developed rapidly, but various pipes still have some deficiencies in varying degrees, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience, stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe.Stainless steel seamless steel pipe for fluid transportation (instead of gbt- instead of gbt- instead of gb-)