Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different,KatowitzBuilding guide rail lifting cargo elevator, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Katowitz,Therefore, before heavy platform operation, the operator should provide the operator with operational skills and safety information, including: operation content and requirements; safety matters and dangerous points; division of labor and scope of responsibility. The operator should not only check the condition of the vehicle and the operator, but also check the terrain environment, whether the flight and landing meet the needs of safety skills or the pre-established operation plan. If there is income and expenditure, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Chokwe,Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The guide rail type elevator is a kind of equipment for transporting heavy objects up and down. It has a very good application in factories, its daily maintenance and maintenance are very important, because some small details If you don't pay attention, so pay attention when doing the daily maintenance of the elevator.In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation and to prevent unnecessary wear and tear.Welcome calls ,Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, and diesel engine.

The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted,KatowitzTen ton lifting cargo elevator, and the pressure gauge reads the pressure gauge.Discount,The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply and diesel engine.Correct use of hydraulic lifts can prolong their service life and play an important role, so how to use them? Professional elevator factory high price, service, on-site settlement, integrity management!Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line,KatowitzSimple and fast lifting cargo elevator, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?Katowitz,Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.