The fruit is also bad; When the axial flow pump is used its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionEnantiomer,　　Note: Motors for special environment can be customized according to the contract.　　It can improve the mechanical efficiency to a certain extent. Moreover the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possibleChangzhi,　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　The Tao part also consumes part of it.　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainly

　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directly　　In fact, as long as we understand the structure and working principle of the slurry pump, this problem is very easy to solve. We all know that the working principle of the slurry pump is to use centrifugal force to transport slurry, so we need to rotate the impeller of the slurry pump, and the connection between the impeller and the pump shaft is connected through screw threads.　　Balance of.recommend,　　Submersible slurry pump can be widely used in mining, power, metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, river dredging, river dredging, etc. In chemical industry　　Reasonable.　　If the oil seal ring of the shaft is seriously worn,EnantiomerSubmersible sewage pump, replace it with a new one.

　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, whensystem,EnantiomerVertical slurry pump,　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　Ah slurry pump internal structure The pump shaft is bent. After the slurry pump reverses, the reaction force of the impeller may directly top the pump shaft. If the rigidity of the pump shaft is insufficient, resulting in the damage of other accessories in the pump.　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.Enantiomer,　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor