It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.The general delivery length of qb square pipe is mm-mm, mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tubeSt. Louis Rio, Colorado,Function index analysis of square tube - strength and plasticity discussed later are machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load employment. In this environment, the whole opportunity is tired.Stage ( & mdash; )Tartagal,A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )Ferrous metals refer to iron and iron alloys. Such as steel, pig iron, ferroalloy, cast iron, etc. Steel and pig iron are alloys based on iron square tube and carbon as the main added element, Rio, ColoradoGalvanized pipe factoryPrecautions for use of tools' >

Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).The purpose of heat is to prevent the generation of cold cracks. Cold crack is directly related to carbon equivalent. Therefore, and the carbon equivalent of the qb square tube is the same. If the carbon equivalent of Q is less than .%, it can be said that the weldability is OK. Generally speaking, the cold crack increases when the carbon equivalent is .%.Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel, ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.Equipment maintenance,The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.

In this period, the technology of continuous rolling pipe was not mature.Honesty is the foundation,Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.Before gas cutting remove the dirt and grease on the steel surface, the movement of the cutting torch shall be kept at a uniform speed. The cutting surface should be ~ mm away from the tip of the flame core. If the distance is too close, the edge of the cut will melt, and if it is too far away, the cutting will be interrupted easily due to insufficient heat.During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used,St. Louis, Rio, Colorado80 galvanized square pipe, the thickness is significantly lower than the standard.St. Louis,St. Louis, Rio, ColoradoGalvanized Q235 square pipe, Rio, Colorado,The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.