Are the water cooling and air cooling of the hydraulic station the same?The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Jincheng,As long as we transport the lifting platformTake the measures that need to be taken during the transportation of the lifting platform in advance to prevent all possible problems and then the difficulties will be solved. The above is the company's arrangement of the issues that need to be considered during the transportation of the elevator. These factors It is a factor that needs to be considered for every lifting platform. Therefore, we must try our best to be perfect and impeccable. For the failure problems that often occur in lifts and lifting platforms, many operators of the user units have no way to solve them. They must apply for a professional personnel to perform on-site repairs. However,Jincheng1 meter fixed lifting cargo elevator, due to the obstacles of the working environment and time factors of the equipment, the failures of the equipment cannot be fully repaired normally, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is,Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains and pulleys are made of solid materials to ensure safety.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.

Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.The second is that steel will have obvious effects of thermal expansion and cold contraction at low temperatures. Although this property of steel will be taken into account when designing and manufacturing hydraulic lifts, after all, the environment is different. Under low conditions, steel will appear. Some unstable performances, such as increased hardness, decreased toughness, etc. At this time, it is necessary to pay more attention to the maintenance of equipment to keep the key parts in order to avoid dry grinding.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?index,If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Today the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.

Check the limit switch to see if all the limit switches are loose. If so,JinchengOrdering Elevators, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts,Jincheng3-meter cargo elevator, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Convenient and efficient,Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Precautions for daily maintenance of hydraulic lifts Check all hydraulic pipes and joints of hydraulic lifts. The pipes must not be damaged, the joints must not be loose, and all joints must be tightened.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?JinchengFixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore