The bearing capacity of decorative stainless steel pipe ice load is the main control load of offshore platform in severe cold area, which has high requirements for the shear bearing capacity of jacket leg of offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. A compound forming process of double-layer stainless steel pipe for primary circuit main pipeline of station is designed, which solves the problem of limited length of finished products in traditional forging or casting process, and meets the special requirements of complex working environment on pipeline performance. The three roll cross rolling forming process of double-layer casing with outer layer -n austenitic heat-resistant stainless steel and inner layer cr-ni martensitic heat-resistant stainless steel was simulated and optimized by using DEFORM-D finite element simulation software. The internal and external deformation, stress-strain field and temperature field of double-layer stainless steel pipe were analyzed, and the optimal deformation parameter combination was obtained by orthogonal test. The simulation results show that in the process of three roll cross rolling, the large values of equivalent stress, equivalent strain and temperature are concentrated in the area between the outer tube and the roll, and the overall performance parameters of the outer tube are greater than those of the inner tube. The range analysis and variance analysis of orthogonal design test show that the optimal deformation parameter is rough rolling temperature deg; C. Feed angle & deg;, Roll speed: rmin. Objective to improve the existing connection mode of the braking system pipe system of railway freight cars, and accurately shape the end of the stainless steel pipe, so as to obtain the forged joint with better mechanical properties. According to the connection mode of the original pipe system and the plastic forming characteristics of steel pipe, a multi-step upsetting and extrusion process for the end of stainless steel pipe is proposed. The process is numerically simulated by DEFORM-D three-dimensional finite element simulation software, precipitation hardening stainless steel and high alloy with iron content less than % are usually named by patent name or trademark.Nassau,(III) steel exports grew rapidly. The supply and demand of domestic steel market is unbalanced, and the export of enterprises. From January to June, China exported . million tons of steel, a year-on-year increase of %; . million tons of steel were imported, down % and tons of billets and ingots were imported, the cumulative net export was . million tons, a year-on-year increase of %, accounting for % of China's crude steel output. In terms of export price, the average export price of bars and wires from January to June was US dollars per ton, a year-on-year decrease of %; US $ tons of plate, a year-on-year decrease of %.Section shape stainless steel pipe can be divided into round pipe and special-shaped pipe according to the section shape. Special shaped tubes include rectangular tubes, rhombic tubes, elliptical tubes, hexagonal tubes octagonal tubes and various cross-section asymmetric tubes. Special shaped pipe is widely used in various structural parts, tools and mechanical parts. Compared with circular pipe, special-shaped pipe generally has large moment of inertia and section modulus, and has large bending and torsion resistance, which can greatly reduce the structural weight and save steel.Zhetiqara,In the interior decoration project, the proportion of water pipes is very small, whether it is data consumption or price. However, once the water pipes show achievements,NassauStainless steel plate suction cup, the results will be very serious. Therefore, it is extremely important to choose water pipes with reliable quality, high volatility, convenient maintenance, health and environmental protection. With the development of the national economy and the progress of people's living standards, people's requirements for domestic water pay more and more attention to health and environmental protection. A good water source escort pipeline has become a careful choice. Water pipes are generally experienced in lead pipes & rarr; Copper pipe & rarr; Iron pipe & rarr; Galvanized iron pipe → Plastic pipe & rarr; Development process of stainless steel pipe. It has become a trend in the world to select high-quality stainless steel materials as water supply pipes. The material indicates that in Germany, more than % of residents choose stainless steel water pipes; In Japan, more than % of households in Tokyo have adopted stainless steel water pipes; In Australia, it has begun to change other pipes to stainless steel pipes; In the United States, the water pipes of five-star hotels in Las Vegas are all made of stainless steel. Since the beginning of the st century, due to the progress of living standards, more than % of residents in China need water pipes to meet their needs of high-quality life. Therefore, high-quality stainless steel materials move from tableware to household water pipes. It has become a trend to select high-quality stainless steel pipes in tooling or home decoration projects. Stainless steel water pipes and stainless steel pipe fittings will become an indispensable part of the building materials market in the future. Stainless steel material is a recognized health material that can be implanted. The manufacture of water pipes based on stainless steel has a long history in developed countries. Stainless steel pipe has gradually become a new choice of water supply pipe with the characteristics of safety, sanitation, environmental protection, and has become the current world trend and development direction. Stainless steel water pipe is called the real green pipe in the st century. With the gradual standardization of stainless steel pipe industry, it can be predicted that the consumption technology and connection technology of stainless steel pipe will also slow down to standardization and become more and more perfect. The development of stainless steel pipe technology will not only create a favorable condition for health, environmental protection and sanitation for national domestic water, but also win a larger market for stainless steel pipe enterprises. Stainless steel pipe entering the construction and decoration market is an attack in the water pipe industry.Stainless steel pipe, which was produced and used in China at the end of the s, is a new family emerging in the field of pipe materials. It has been widely used in building water supply and direct drinking water pipelines.Meet the needs of architects and structural designers.

The main control load of the platform has high requirements for the shear bearing capacity of the guide leg of the offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, concrete strength, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the smaller the shear strength. Combined with the test, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength, diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength,Nassau100mm stainless steel square pipe, the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. Based on the jacket offshore platform, it is proposed to replace the four hollow steel conduit legs of the original offshore platform with concrete-filled steel tube in stainless steel tube to form a new composite offshore platform with concrete-filled steel tube in stainless steel tube, so as to improve the ice resistance and disaster prevention ability of the offshore platform. The scale test on the offshore platform shows that the composite offshore platform of concrete filled steel tubular in stainless steel pipe (hereinafter referred to as the composite offshore platform) has better anti icing performance than the ordinary jacket offshore platform. Taking push as an example, the peak acceleration and displacement of the upper deck of the composite offshore platform of concrete filled steel tubular in stainless steel pipe are reduced by % and % respectively. The analysis of ABAQUS finite element and experimental simulation results shows that the error of the two results can be basically within %. Through the simulation analysis of the ultimate bearing capacity of the stainless steel tube in tube concrete-filled steel tubular composite platform and the original offshore platform it can be seen that the stainless steel tube in tube concrete-filled steel tubular composite platform has stronger ultimate bearing capacity. Therefore, the composite offshore platform of concrete-filled steel tube in stainless steel tube is a good new type of jacket offshore platform. Axial compression tests were carried out on austenitic and duplex stainless steel tube concrete short columns. The ultimate load, longitudinal strain and circumferential strain of the short columns under axial compression were measured. The effects of steel tube wall thickness and concrete strength on the bearing performance of the short columns were investigated. Reference was made to the European Code for design of concrete filled steel tubes (Eurocode), prepare construction scheme and construction schedule scheme China's relevant regulations D --dlt- and CECS calculate the preparation of stainless steel pipe construction, and establish quality standards.　　— It has better temperature resistance.Stainless steel why corrosion-resistant stainless steel decorative pipe stainless steel pipe, stainless steel pipe, all metals react with oxygen in the atmosphere to form an oxide film on the surface. Unfortunately the iron oxide formed on ordinary carbon steel continues to oxidize, expanding the corrosion and finally forming holes. The carbon steel surface can be guaranteed by electroplating with paint or oxidation resistant metals (e.g. zinc, nickel and chromium), but as is known this protection is only a thin film. If the protective layer is, the steel below begins to rust.Production department,With the implementation of China's reform and opening up, the national economy has achieved rapid growth, and a large number of urban houses, public buildings and tourism facilities have been built, people pay more and more attention to the problem of water quality, and the requirements are also increasing. Galvanized steel pipe, a common pipe, will gradually withdraw from the historical stage under the influence of relevant countries because of its corrosivity. Plastic pipe, composite pipe and copper pipe have become common pipes in the pipeline system. However, under certain circumstances, stainless steel pipe has more advantages, especially the stainless steel pipe with wall thickness of only . ~ mm. In high-quality drinking water system, hot water system and water supply system that puts safety and sanitation first, it has the characteristics of safety, reliability, sanitation, environmental protection, energy-saving and environmental protection pipes with good comprehensive performance of water supply system. It is also a very competitive water supply pipe, which will play an incomparable role in improving water quality and people's living standards.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.Stainless steel pipe is durable and has been recognized by the engineering community, and relevant parties are starting from reducing the wall thickness and lowering the grid,NassauStainless steel mesh belt for food, so as to facilitate further development. In particular, the price of stainless steel pipe is not high, so the supporting connection, the reliability and price of pipe fittings are the main factors determining its development. Domestic developers have independently developed connection technology and pipe fittings in Sichuan, Guangdong, Zhejiang, Jiangsu and other places, which is a promising pipe. The Ministry of construction and relevant departments also attach great importance to this new type of pipe. According to China technology market management promotion center and gksz [] No. document on Application & ldquo; High diameter to wall ratio and high precision stainless steel medium and high pressure water supply pipes and supporting fittings and special technology & rdquo; It is learned from the notice that the application of stainless steel pipe technology and product is of great significance to improve the grade of modern buildings in China and improve and ensure the water quality of water supply.

When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .The cost is reasonable,In engineering, the following methods are often used to prevent intergranular corrosion: reduce the amount of carbon in steel so that the amount of carbon in steel is lower than the saturated solubility of austenite in equilibrium, that is, fundamentally solve the problem of precipitation of chromium carbide (crc) on the grain boundary. Generally, the requirement of intergranular corrosion resistance can be met when the amount of carbon in steel is reduced to less than .%.Organic substances (such as melons and vegetables, noodle soup, phlegm, etc.) adhered to the surface of stainless steel constitute organic acids in the presence of water and oxygen. For a long time, the corrosion of organic acids on the metal surface.Stainless steel seamless steel pipe for fluid transportation (instead of gbt- instead of gbt- instead of gb-)NassauThe back is not protected by argon, and the flux cored wire + TIG process has been applied in China for several years. Flux cored wires such as et-elt-et-elt-t-et-elt- have been produced and applied to field welding and good economic benefits have been obtained.Rheological and thermal changes in the quenching process of decorative stainless steel pipe the cooling characteristics of submerged quenching of stainless steel plate are numerically simulated by using the Euler multi fluid model in AVL fire software, and the numerical results are compared with the experimental results. In the research, the quenching medium is water. The mass, momentum and energy equations of gas-liquid two-phase of quenching medium and the quenching heat conduction equation of stainless steel workpiece are solved by numerical simulation. Based on the principle of equal heat flux between quenching medium and workpiece, and can be extended to the multiphase flow simulation in complex system to guide the actual production. The single pass thermal simulation compression experiment of Cr super martensitic stainless steel was carried out by Gleeble thermal simulation tester to study the thermal deformation behavior at ~ ℃ and strain rate of . ~ s-, and the microstructure evolution law of grains under different conditions was analyzed; Based on Sellars hyperbolic sinusoidal model, the flow stress constitutive equation of Cr super martensitic stainless steel was constructed. The results show that the peak stress decreases with the increase of deformation temperature and the decrease of strain rate; With the increase of deformation temperature, the dynamic recrystallized grains are obviously refined. The thermal deformation activation energy Q = . JMOL of decorative stainless steel pipe is calculated, and the expression of Zener Hollomon parameter is obtained. Different feedstocks were prepared by mixing crmnmon nickel free austenitic stainless steel powder prepared by aerosol and wax based binder. The effects of binder ratio and powder loading on the rheological properties of feed were studied by rh high pressure capillary rheometer. Non Newtonian index n, viscous flow activation energy E and comprehensive rheological factor alpha are calculated by second order model regression analysis; STV. The results show that the prepared feeds are pseudoplastic fluid. The binder system was composed of % microcrystalline wax (MW), % high density polyethylene (HDPE), % ethylene vinyl acetate copolymer (EVA) and % stearic acid (SA). The powder loading was vol%. The feed had good comprehensive rheological properties. In order to study the cementitious properties of stainless steel AOD slag, stainless steel AOD slag was used to replace some cement, and its effects on the working properties and mechanical properties of cement mortar were studied. The results show that using stainless steel AOD slag to replace cement from ~ % with the increase of the content of stainless steel AOD slag, the water consumption of standard consistency of cement first decreases and then increases. When the content is %, the strength of cement mortar decreases in turn, indicating that the cementitious activity of stainless steel AOD slag is small.Application field: tubular boiler for pipeline in harsh seabed environment product description: ultra (ultra) critical unit is the basis of modernization of power generation equipment and energy conservation and emission reduction. Among the important pressure parts of ultra (supercritical) boiler, superheater and reheater are the parts with high working temperature and bad working environment. Previously, all such materials used in China were imported from abroad, expensive import prices, difficult procurement and short supply, which seriously affected the production of ultra supercritical boilers and the development of electric energy in China. At present, China's demand for utility boiler tubes is about tons, and with the continuous improvement of ultra (supercritical) power generation technology, the demand is expanding. Several large domestic enterprises have invested a lot of human and financial resources in the R & D and production of such products, and have made considerable achievements. On the one hand, it has made its own contribution to the development of national electric power industry, but also brought considerable economic benefits to enterprises.