Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　 When starting the slurry pump,Victoria de Las TunasWear resistant slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motorVictoria de Las Tunas,　　Domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, renovation, digestion and innovation. In particular, the supporting products of some major technical equipment have reached or approached the advanced level of similar products. With the continuous expansion of the market, stainless steel pipeline pump　　It is located in the middle, so it seems that many regions have good effects when using it.Kotido,　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used,Victoria de Las TunasCorrosive pipeline pump, so it is effective when it is used in many mountainous areas　　Submersible slurry pump can be widely used in mining, power, metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging, river dredging, etc. In chemical industry　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected,Victoria de Las TunasWater well pipeline pump, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid

　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　If it is large the guard plate is likely to be damaged on the spot, the jacket is likely to have cracks, and the blades of the impeller will also be greatly impacted. The most serious thing is that all the flow passage parts are damaged.　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.details,　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults

　　Pump, sewage submersible pump and seawater submersible pump.Convenient and efficient,　　What is the solution to this situation?　　 daily, weekly, quarterly and annual inspection, maintenance and use plans shall be prepared for deep well pumps.　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!Victoria de Las Tunas,　　With the continuous development of slurry pump technology, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　With the continuous development of slurry pump technology, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, the pump head shall be determined by enlarging the margin of % - %.