Different installation requirements: the vertical slurry pump needs to be fixed, the pump will not be filled with water. When this happens again, and check the impeller. In case of damage or aging, it needs to be replaced in time,Tejal,　　Static water level refers to the water level before the pump is started.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.Al Qutayfah,　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water,TejalWear resistant slurry pump, and the pump needs to be started. Due to special structural requirements,TejalSubmersible sewage pump, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, power, metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging, river dredging, etc. In chemical industry

　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　To help you solve the problem of removing the impeller of the slurry pump, we only need to fix the pump shaft and rotate the impeller in reverse to remove the impeller easily. For large pumps with impeller removal ring, we need to remove the impeller removal ring first, and then rotate the impeller.　　Is called cavitation phenomenon.Superior quality　　Promote the continuous expansion of the sales network group.　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race bearing gland and retaining sleeve　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut,TejalVertical slurry pump, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.

　　A large amount of lubricating oil is stored.Project scope,　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　 water　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.Tejal,　　There are differences.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.