The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generatorsSaint Vicente,　　 If the three-phase current of the submersible sewage pump is large and stable, such as those wrapped around the pump shaft　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.Saltillo,　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　 Moreover, the processes of these two pumps are also different and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump,Saint VicenteVertical non clogging sewage pump, dredging pump the impurity pump, desilting pump, etc. are all in the application scope of the slurry pump

　　The slurry pump of underground pump can also work normally.　　The horizontal slurry pump is a cantilever centrifugal slurry pump, which is suitable for conveying abrasive or corrosive slurry. The structures of all types of horizontal slurry pumps are similar except that the pump head (including pump body, pump cover, impeller, etc.) has different structures. The pump head part, shaft seal part and transmission part　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this it and the generator naturally become popularSupply chain quality management,　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　Let the medium containing some solid particles generate a certain flow rate, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use

　　When using the sand pump,Saint VicenteVertical heavy-duty slurry pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoidQuality improvement,　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　Consider the vertical separation level of the tail equipment.　　No matter what type of slurry pump you need,Saint VicenteSewage pump diving, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!Saint Vicente,　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.