When the slurry pump is working, the pump needs to be placed on land the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　What is the order.Saint spiritus,　　Through human auditory , we can compare whether the pump has heavy, miscellaneous, strange and disordered abnormal noise, and can judge the hidden dangers such as looseness, impact and imbalance.　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.Indore,　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Now you know the reason why the pump has air turbidity. In fact, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.

　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect,Saint spiritusDrilling fluid slurry pump, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　Pipeline pump, is a single-stage centrifugal pump with standing structure. Because the layout design of its water pump inlet and outlet is relatively special, they are all located on the same straight line, and their inlet and outlet diameters are the same, the overall description is similar to a section　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.Professional is king,　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.

　　When the pump is not in use the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionsuperior quality,　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, resulting in low speed.　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurrySaint spiritus,　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　About %),Saint spiritusLong shaft submerged slurry pump,Saint spiritusQJ submersible pump, and motor power p=i × U indicates that high power and current will increase.　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be