Second, soak in water.The third kind: you can smell the faint smell of wood. This floor shows that there is little glue content.It can reach European standard E levelEscuintra,Fear of water and moisture: the base material of laminate floor is medium and high density board, with small relative density and large expansion coefficient. Once the reinforcing layer is filled with water after paving, if it is not wiped in time,EscuintraSelection of floor leather, it is easy to cause blistering and deformation due to water absorption and expansion. Its moisture resistance is not strong, and its stability is poor in humid environment.Impregnated paper laminated wood floor is a floor made of one or more layers of special paper impregnated with thermosetting amino resin, which is paved on the surface of wood-based board substrate such as particleboard and high-density fiberboard, with a balanced moisture-proof layer on the back and a wear-resistant layer and decorative layer on the front. It is hot pressed and formed. First, it is divided into thin and thick (more than mm and about mm in thickness).Dura,Use place of SPC floor: because of its thin thickness, many colors, complete styles and low-carbon environmental protection performance it can be widely used in kindergartens, offices hospitals, office buildings, homes, KTV and other public places. Ecological and environmental protection.The flame retardant grade is B and the indoor formaldehyde is higher than the national standard.： I can&#;t tell the taste. The domestic price of this floor is more than yuan;

Some people say this method is unscientific and laminate flooring can&#;t soak in water, but I have done some experiments and come to another conclusion.The main stressed parts of the floor, such as keel panel layer, shall not have large scars or cracks.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand,EscuintraWhich is a good SPC floor,EscuintraWaterproof wood floor, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one) apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Quality assurance,The current woodworking is basically done by woodworkers. The 'general woodworking' method is adopted, and the shrinkage joint size is not calculated according to the thermal expansion and cold contraction parameters provided by SPC flooring factory.If the room is slightly larger, but the reserved gap is too small, especially when the temperature difference between winter and summer is too large, it is very easy to have no gap to expand, resulting in arching and warping.Twelfth, heat transfer, cold prevention and warmth preservation.Polymer base material layer: a composite plate made of stone powder and thermoplastic polymer materials after stirring evenly and then extruded at high temperature. At the same time, it has the properties and characteristics of wood and plastics. Therefore, this floor has good strength and toughness. Ecological environmental protection;

I have seen the evaluation video before. Netizens rub the steel ball of cleaning tableware back and forth on the SPC floor, and there is no trace on the surface.If it&#;s a wooden floor, I think it&#;s not like it anymore. You can see how good its wear resistance is.Quality management,In order to reduce the cost, SPC latch floor with extremely poor quality and low price is adopted, which has poor stability and large thermal expansion and cold contraction.The loss is caused by the 'general paving method'.Surface treatment technology affects the price of laminate flooring.With the change of market demand, the floor surface treatment process is more and more diversified, and the decorative effect is more and more obvious, such as antique, relief and decorative effect.The floor price using these methods is much higher than the standard floor price.Intelligent decoration design everyone is optimistic about environmental protection. After all, formaldehyde pollution is the primary decoration design environmental pollution that harms health.And laminate as a medium density and high-density commodity, in many cases, customers are unwilling to choose, laminate does not protect the environment, as if it has become a hard logo.But in fact, only the wood itself is basically with glue.Although the environmental protection quality of super glue is very high,Main differences between WPC and SPC flooringThe surface coating of piano paint is actually the paint used on the surface of solid wood floor for laminate floor. It is only bright paint. The wear resistance of this coating is far from that of aluminum oxide surface. Its wear resistance is low, and solid wood floors are developing towards high wear resistance. Unless you like the coating of this surface.There is nothing in the world that is not hot, and so is the floor.No matter whether the SPC floor has shrinkage joints or not, as long as the shrinkage joint size is calculated according to the shrinkage performance of the floor, site environment, room size, winter and summer temperature, even the floor with poor robustness can minimize the problem rate and reduce unnecessary losses.The development trend of China&#;s solid wood flooring industry chain is from big to strong. On the other hand, it also depends on the training of various difficulties and events in the markets of all countries in the world.The tsunami caused fluctuations in the wood market, followed by the rise in the price of solid wood flooring in , the decline in total consumption output, and more fierce market competition. In particular, the announcement of the current policy of levying % income tax on the Chinese market of solid wood flooring in also pushed the solid wood flooring company to the vortex of public opinion.Therefore, China&#;s solid wood flooring field should re plan the overall goal of development prospects, adjust the development strategic concept, actively build a strong brand and promote the physical and mental health development trend of solid wood flooring.