In order to ensure the appearance quality of continuous casting slab, select appropriate maintenance slag; During continuous casting, the vibration marks formed on the surface of continuous casting slab due to the vibration of mold shall be; Electromagnetic stirring must be used in continuous casting of ferritic stainless steel pipe fittings.The operators are mainly plumbers and argon arc welders, with the cooperation of other types of work, and the argon arc welder shall have the certificate issued by relevant departments.Nova Zagora,Remarks: to ensure the nickel content of stainless steel strip and the mechanical properties of stainless steel strip, material certificate (Baogang material), Japan Nippon Steel Material Certificate (Nippon Steel material), SGS report, etc. can be provided.When using this method, it should be noted that the water-soluble paper should be double-layer and must be pasted well, otherwise it is easy to cause damage and fall off of the water-soluble paper, resulting in loss of argon protection of the inner weld and oxidation, resulting in cutting of the weld junction and re welding, which can not ensure the welding quality and seriously affect the construction period. Therefore, the water-soluble paper should be strictly checked and pasted before welding.Pekanbaru, the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the steel plant is that the peeling and trachoma of the steel strip will cause rust. Substandard materials will cause rust. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the pipe manufacturer: the welds in the pipe manufacturer are polished rough, which will cause rust.Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and , martensitic stainless steel is marked with and C, dual phase (austenite ferrite).In engineering, the following methods are often used to prevent intergranular corrosion: reduce the amount of carbon in steel so that the amount of carbon in steel is lower than the saturated solubility of austenite in equilibrium, that is fundamentally solve the problem of precipitation of chromium carbide (crc) on the grain boundary. Generally, the requirement of intergranular corrosion resistance can be met when the amount of carbon in steel is reduced to less than .%.

After molten steel casting, stainless steel pipe fittings generally adopt the same vertical, vertical bending or arc continuous caster as carbon steel. The refined molten steel is poured into the ladle, the ladle to be poured is transferred above the tundish mouth through the rotary table, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming condensation and continuous downward movement.　　— Good ductility,Nova Zagora904L plate stainless steel, and argon with purity of % shall be selected. If the content of impurities is too highArgon shall conform to the rules of national specifications, the maintenance effect of argon will be weakened and the weld quality will be indirectly affected.Continuous casting shall be adopted for stainless steel pipe fittings, so as to improve the comprehensive yield, and cooperate with out of furnace refining, which significantly improves the production efficiency, omits the blank opening process and saves a lot of energy consumption.Stainless steel pipe packing bag is nothing more than the function of protecting the surface of stainless steel pipe, so most stainless steel pipe users do not have to question this point.

Stainless steel seamless steel pipe for fluid transportation (instead of gbt- instead of gbt- instead of gb-)how muchChloride ions exist in the service environment. Chloride ions exist widely, sweat, sea water, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions even more than ordinary low carbon steel. Therefore,Nova ZagoraWelding method of stainless steel pipe, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, there are different tolerances for seamless hot expanded pipe, seamless cold rolled pipe and welded pipe according to different dimensions. For example, for hot expanded pipe with diameter less than mm, when the thickness is mm and less, the upper limit tolerance of thickness is %; If the standard of stainless steel pipe is Chinese standard, according to the tolerance of stainless steel pipe for fluid transportation in gbt, the tolerance here is the tolerance when ordering according to the nominal thickness; According to the manufacturing method, the thickness standard of stainless steel pipe is divided into hot rolling and cold rolling, including thin plate with thickness of .-mm and thick plate with thickness of -mm. The specific gravity of stainless steel pipe is . The weight = specific gravity of length and width of thickness, and the weight of plate with thickness of stainless steel pipe of mm = m m = kg m (length) m (width) . M (thickness) (specific gravity) = . tons (weight)During welding, the process of ventilation in advance and gas stop behind shall be adopted, and the adhesive cloth on the outside shall be torn off while welding. Because the blocking plate is composed of rubber and white iron sheet, it is not easy to be damaged, so this welding can well ensure that the inner side of the weld is filled with argon and its purity, so as to effectively ensure that the metal on the inner side of the weld is not oxidized and ensure the quality of weld backing welding.Nova Zagora,Welding of stainless steel pipe argon arc welding stainless steel pipe: it is required to have deep penetration, no oxide inclusion, and the heat affected zone can be as small as possible. Argon arc welding maintained by tungsten inert gas has good compliance, high welding quality and good penetration function. Its commodities are widely used in chemical, nuclear and food industries.After fine tuning the molten steel temperature in the argon blowing station, it is lifted to the ladle rotary table for continuous casting.When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.