In addition to the method, anti cavitation theory, protection should be done well, which should be a comprehensive optimization design method.　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.Indianapolis,　　If it is large, the guard plate is likely to be damaged on the spot, the jacket is likely to have cracks, and the blades of the impeller will also be greatly impacted. The most serious thing is that all the flow passage parts are damaged.　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationzaire,　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling,IndianapolisVortex pump and pipeline pump, the motor temperature will rise, so it is easy to burn out the motor.　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.

　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　 The reasons for excessive power loss are as follows: the running speed of the screw rod is too high.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Welcome calls ,　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.

　　 If the power cord is not well contacted, it will also lead to the burning of the motor.packing,　　 in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact,IndianapolisCirculating hot water pipeline pump, such measurement is not very accurate.　　 The personnel on duty for daily inspection and maintenance of the submersible pump shall make one listening, two looking, three touching and four recording.　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation,IndianapolisWater well pipeline pump, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.Indianapolis,　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　When in use it can drive the impeller to rotate so as to drive it to flow.