When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?Houston,　　When there is glove or towel fiber in the water, there will still be stemming.　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.Mumias,　　Generally, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, not because the slurry pump has a problem, but because　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent

　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　 No maintenance: if it is not used continuously after startup the submersible pump will rust and cannot be started. If it is not used for a long time, do not immerse it in water for a long time. Put it into clean water and run it for a few minutes to clean the mud inside and outside the pump.　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerProcess inspection,　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.

　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look todayPromise and keep promise,HoustonPipeline pump,　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　 The personnel on duty for daily inspection and maintenance of the submersible pump shall make one listening, two looking, three touching and four recording.　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be greatHouston,　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer,HoustonWQ submersible pump parameters, and dry it naturally.　　The two have certain commonalities. They are both submersible. As the name suggests,HoustonDeep well pump, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.