At this point, if the high-altitude work platform is overloaded, two wheel tractionWalking: assisted self-propelled, self driving, professional company, timely supply, high cost-effectiveness, has become the preferred brand for many wire products. Welcome to purchase!During use, the elevator should be placed on a solid and flat ground to prevent tipping during operation. Press&quo; Rising; Or&quo; Descending; Press the button to frequently check and maintain the various components of the elevator when lifting the workbench. If the workbench does not move, it should be immediately stopped for inspection. When the working pressure of the electric elevator is found to be too high or the sound is abnormal, it should be immediately shut down for inspection to avoid serious mechanical damage; Regularly check the working status of the shaft pin every month. If any loose shaft pin or screw is found, it must be locked tightly to prevent accidents caused by the shaft pin falling off.Izmir,Check, adjust, and replace defective parts of the heavy operating rod mechanism; Clean the valve components; Check the cleanliness of the hydraulic oil valve core for clamping (manufacturing, installation issues, dirt issues)Remove and disassemble the lowering valve, and then reinstall it.Check,Nuremberg Hydraulic automatic lifting platform, adjust, and replace defective parts of the heavy operating rod mechanism; Clean the valve components; Check the cleanliness of the hydraulic oil valve core for clamping (manufacturing, installation issues, dirt issues)

Improper use of oil: Inadequate maintenance of high-altitude work platform equipment such as mobile elevators can also lead to small fitting gaps of components, making it difficult for oil to form a uniform oil film on the friction surface. Additionally, due to assembly and other reasons, it is difficult to ensure the uniformity of fitting gaps, thereby reducing efficiency and causing early abnormal wear of equipment components; In severe cases, it may cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of abnormal equipment noise.Usually, the connection status of each part is checked, and if there is any looseness, it should be tightened. The tightness of the body connecting bolts should be checked when the body is under pressure. All connecting shafts must have split pins and must be fully unfolded.When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges slopes, or cliffs,Nuremberg Customized hydraulic lifting platform, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.Pursuit of excellence,Hydraulic oil should be kept clean and replaced every months; When repairing, maintaining, and cleaning the elevator, be sure to support the support rod.The guide rail type cargo elevator has been inspected and debugged before leaving the factory, and all technical indicators have met the design requirements. When in use,Nuremberg Hydraulic straight top lifting platform, only the power supply needs to be connected, and the hydraulic and electrical systems do not need to be adjusted.Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, eliminating hidden dangers, and troubleshooting are beneficial for improving work efficiency, extending equipment service life, and ensuring the safety performance of elevators.Industry management,Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.When installing, disassembling, and adjusting the exhibition organization, attention should be paid to ensuring that the center line of the exhibition organization reducer is parallel to the center line of the gear, and its meshing surface is not less than %, and the meshing interval should be appropriate.When using the distribution box the electric leakage switch meets the requirements for construction elevators. If the fixed elevator installed is variable frequency, the selection of the leakage switch should be compatible with the frequency converter.Nuremberg ,At this point, if the high-altitude work platform is overloaded it may cause damage to the components and cause some mechanical failures.Use a heavy crane to lift the cage and lift it from above the standard sectionTalking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.