Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Dusseldorf,It is strictly forbidden to use helmets beyond the validity period. The validity period of helmets is counted from the date of delivery. Plastic helmets shall not exceed two and a half years, and fiberglass helmets shall not be used for more than three and a half years.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Ciudad-ViejaBefore using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.

If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.What is the pressure of the lifting platform? The movement of the lifting platform has always been our concern now. Our use occasions are uncertain, in order to better favor customers, we are constantly researching lifting with good mobility. Platform, which can be used in different occasions, but for some large logistics companies or some enterprise processing plants, we are still used to using fixed lifts. It has a huge load capacity and is very stable and strong which can meet the needs of many customers. This is also In recent years, domestic lifting platforms have been used.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.quality standard,Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?

Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Free consultation,The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding the short-circuit current is much larger than the normal operating current, causing the winding to overheat and even burn out.Cleaning and keeping it clean is the first priority. Regularly clean up the dust or sundries on the motor of the hydraulic lifting platform, otherwise the long-term accumulated dust will fall into the motor fan, and it will be very difficult to run, just like the laptop we usually use. If the dust on the computer fan is not cleaned, the computer will not be easy to dissipate heat, or even buzz. It will be much better after cleaning, and the same is true for the motor of the hydraulic lifting platform. V or V; how to properly maintain the motor of the hydraulic lifting platform to avoid the motor, of course, it is safer to keep away from the water for things related to electricity, do not use it outdoors in rainy and snowy weather, etc., and pay attention to the selection during storage The environment is clean and dry; it is strictly forbidden to overload the hydraulic lifting platform. When using the hydraulic lifting platform, it must not be overloaded, which will bring a burden to the motor, and it may burn out the motor; At this time, you don’t have to worry about whether it is overloaded during use. It is not too expensive to add this device. Safe, more at ease); can not adjust the overflow valve (also known as 'solenoid valve')Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory old brand, price advantage,DusseldorfFactory lift cargo elevator, quality guaranteed!Dusseldorf,Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece,DusseldorfProfessional cargo elevator, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, car lifting, fixed three-dimensional parking and other places.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .