H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.I-beam, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.Grodno, Product description of galvanized pipe Peak crackEspieux,Dry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage,Grodno12Cr1MoVG high pressure alloy pipe, a layer of zinc is deposited in the pipe.When selecting I-beam in structural design, weldability and structural size. I-beam is mainly divided into ordinary I-beam chemical properties, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams.

After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution,Grodno16Mn thick wall seamless pipe, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Oxygen blowing welded pipe: it is used as steel blowing pipe. Generally, small-diameter welded steel pipe is used. There are eight standards from / inch to inch. Made of , , or q-q steel strip. In order to prevent corrosion, some are aluminized. Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.Welcome to inquire, Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.C-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life,Grodno40CrNiMo alloy pipe, corrosion resistance and durability. It is a kind of stronger protection.The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.

What are the requirements for alloy pipe construction accessoriespacking,Application scope of alloy pipePipelines of various specifications and models are complete. Frame line crackGrodno,Main uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery.Stages needing attention in the production and manufacture of alloy tubesH-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.