Komarom Car lift cargo elevatorWhat are the key points of the design plan
2024-02-05 04:16:57The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.The main structure and application of the guide rail elevator adopt closed gear transmission. The large and small gears are made of steel. The design is calculated according to the fatigue strength of the tooth surface, connecting pipes and connecting pieces. You can choose any product, and the professional elevator factory has safe and secure transactions. At the same time, in order to reduce the weight of the bracket, many craft holes are designed on the two side plates. Because the worm gear mechanism has the advantages of large transmission ratio, compact structure, small impact load, stable transmission and low noise, it also has the characteristics of reverse self-locking. It can ensure that the transmission mechanism can self-lock when the motor is powered off during the process of transporting patients, so the worm gear reducer is selected. The involute worm is used, and the helical surface is quenched to improve the transmission efficiency and increase the wear resistance. The material of the worm gear is polyoxymethylene. The plastic worm gear has the advantages of good processing economy, stable transmission, vibration absorption and noise reduction,Komarom 1 meter fixed lifting cargo elevator, light weight wear resistance and self-improvement, which makes the design of the elevator more humanized.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.assets,The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported,Komarom 10 ton lifting cargo elevator, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Mechanisms: Mechanisms such as tabletops,Komarom Elevating cargo elevators from first to second floors, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.
Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Management Department,Outriggers: mechanical outriggers hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.When the distribution box is used, the leakage switch meets the requirements for construction elevators. If the installed fixed elevator is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Komarom ,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .