I-beam, also known as steel beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.GB No. I-beam is in height, in leg width and in waist thickness.Kamez,The smooth of steel pipe is mainly through tension reducing, which is a continuous rolling process of hollow base metal without center and tip. Under the condition of ensuring the capillary welding quality, the whole welded pipe is heated to more than ℃ by the welded pipe tension reduction process, and then rolled to finished pipes with various outer diameters and wall thicknesses by the tension reduction machine ( times in total). The fluid pipes produced by developed countries in the world have adopted the welded pipe smooth process in a large number of boiler pipes. With the development of society, Domestic hot welded pipe has gradually formed a situation to replace smooth pipe.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe,KamezHow much is 30 I-beam per meter, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Durazno,When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space. According to the diameter of the pipe, the pipe with small diameter can only be welded on one side and the technician can drill into the pipe to weld on both sides. Single side welding requires the welder&#;s technology, which can be formed by welding two on one side. Through the steel ball test, it can ensure that the cross-sectional area passing capacity and weld formation meet the design requirements.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.total cost,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal,Kamez27SiMn seamless pipe price, eliminate structural defects reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Due to the unique performance of I-beam, I-beam has successfully solved the problem of serious equipment wear in many industries.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.

I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.There are many types of galvanized pipes, mainly including cold plated seamless pipes and hot-plated seamless pipes. But now the previous one is no longer used. The hot-dip seamless tube is still in use. Hot dip galvanized pipe is mainly used for steel pipes with low pressure fluid such as water and gas. When in use, if in normal working environment, the thickness of galvanized layer of hot-dip galvanized seamless steel pipe is up to μ M above, and it has been used safely for about years. It can be seen that its service life is very long. Of course, when purchasing, we should also find regular manufacturers to order. Only in this way can we achieve this service life. As long as the galvanized pipe is cleaned after pickling, it is basically cleaned in ammonium chloride or zinc chloride aqueous solution or ammonium chloride and zinc chloride mixed aqueous solution tank. In order to ensure the quality electro galvanizing will not be used. There are also some small enterprises in the market. They will use electro galvanizing in production. In this way, although it is much cheaper in price. However, the quality is very good when used, and it is also easy to have problems. Judged as failing.Kamez,Ways to obtain surface compressive stress characteristics of alloy tubesAlloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects,Kamez304L stainless steel seamless pipe manufacturer, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination generally :, which makes the outer flange thin and the inner flange thick. Therefore, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.