Key technical characteristics of alloy pipe:Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Delamondville, It is the trend of the development of steel bar industry to take the road of steel bar welding mesh in steel bar construction.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Mahalapye, Peak crackThe flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Performance parameters and application scope of I-beam

What are the uses of I-beam? The cold-rolled stainless steel pipe has the advantages of large yield coefficient,Delamondvillethree hundred and twenty-five × 10 welded pipe manufacturer, no expansion, bending and so on. In order to reach the health grade standard of stainless steel pipeline, the pipeline after cold rolling must undergo bright annealing, demagnetization, pickling, calibration and other procedures. Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.technical service,The side length of I-beam is small and the height is large, so it can only bear the force in one direction.Due to the unique performance of I-beam, I-beam has successfully solved the problem of serious equipment wear in many industries. Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.

The specification of pass design I-beam is expressed in cm of waist width. For example the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam,DelamondvilleWholesale of welded pipe, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Discount,Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.From the current scope of use, it is mainly widely used in glass curtain wall, power tower, communication power grid and other industries. In recent years, it has been widely used in many regions and industries, which is enough to show that the quality of galvanized pipe is very good, and it also brings a lot of convenience in the process of use, so it can be used better.Ways to obtain surface compressive stress characteristics of alloy tubesDelamondville,Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, we will use some flanges and elbows to fix them so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, they must be installed together.It is often asked that the shape of I-beam is similar to that of H-beam. What is the difference between them? Many people can&#;t explain it in detail. Here is a detailed answer for you: many people think that I-beam is a domestic name and H-beam is a foreign name. In fact so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, this cognition is wrong. H-beam and I-beam are different in shape!Defects of alloy pipe and solutions: