High altitude work requires the use of tool bags, just press the operation button, and the height adjustment board of the equipment will automatically rise; Release the button, adjust the weight of the plate to fall, and the tongue plate can be used by placing it on the truck.Fot, there should be no dirt on the friction surface. If there is any dirt, it needs to be washed off with gasoline or thinner; The reduction gearbox, gearbox, external meshing gear, and other parts of the equipment, as well as the hydraulic oil, must be tested according to the requirements in the table; The correct maintenance method for hydraulic guide rail elevators is to regularly check the steel wire ropes in various parts for any breakage or looseness. If this phenomenon is found, it should be tightened in a timely manner. The tightness of the connecting bolts of the equipment should be checked when the body is under pressure. All connecting shafts should be equipped with split pins; According to regulations, check the normal operation of each mechanism, whether there is noise or malfunction, and promptly eliminate all faults; When installing, disassembling, and adjusting the rotating mechanism of the equipment, it is important to ensure that the centerline of the reducer and gear is parallel and the meshing clearance is appropriate; Regularly conduct a comprehensive inspection of the equipment to check if there is any damage to the wires and cables, and if there is any overheating of the motor. Replace and eliminate the fault in a timely manner before continuing operation; Ensure the bearings of the motor, and ensure that all boxes, distribution boxes, and brushes are properly protectedReplace with new oil and do not intermittently use old oil, otherwise the moving parts in the system will accelerate wear.Saint NicholasAny product always has a break-in period when it is first used, so what precautions should we pay attention to during the break-in period when using a hydraulic lifting platform? Today, the editor will share this topic with everyone.The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %

Hydraulic oil should be kept clean and replaced every months; When repairing, maintaining, and cleaning the elevator, be sure to support the support rod.Dirty normally closed valve; The solution is to remove the normally closed valve and use cleaning agent or cleaning. Long term scissor fork lift manufacturers have a complete range of products,FotPrice of lifting hydraulic platform, excellent quality and discounted pricesWhat are the common faults of hydraulic lifting platforms? The hydraulic lifting platform's oil cylinder is severely damaged, and uneven damage to the inner sealing ring or obstacles inside can easily cause uneven stress, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.production costs,The pressure of the lifting platform is very important. When lifting goods, the pressure of the lifting platform will test the weight of the goods. If it is overloaded, the general lifting platform will prompt, which serves as protection. Therefore,FotHydraulic lifting platform and hydraulic lifting platform, now lifting platforms are equipped with pressure gauges. Hydraulic machinery should remind everyone to pay attention to the following points: the precautions for using small lifting platforms are based on pressure. Their load-bearing capacity is very poor and their size is small. When using the lifting platform, it is necessary to pay attention to its use. If overloaded, it will cause structural damage to the lifting platform. We have mentioned this many times before when using it.Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, add enough oil and clean the filter. The fuel supply pump has drawbacks: check or exchange the pump.How to maintain elevators in winter is one reason and the primary reason. Many workers in other industries do not know that hydraulic elevators use different types of hydraulic oil in summer and winter. Often, at low temperatures, the hydraulic oil used in summer can become, or even freeze. After entering low temperatures in winter, it is important to remember to replace hydraulic oil containing antifreeze, which is suitable for working at low temperatures.

When working in a hot environment, pay attention to heat dissipation.Product range,During use, the elevator should be placed on a solid and flat ground to prevent tipping during operation. Press&quo; Rising; Or&quo; Descending; Press the button to frequently check and maintain the various components of the elevator when lifting the workbench. If the workbench does not move, it should be immediately stopped for inspection. When the working pressure of the electric elevator is found to be too high or the sound is abnormal, it should be immediately shut down for inspection to avoid serious mechanical damage; Regularly check the working status of the shaft pin every month. If any loose shaft pin or screw is found, it must be locked tightly to prevent accidents caused by the shaft pin falling off.The above introduction to common faults of hydraulic boarding bridges can be said to be very detailed. I hope everyone can respond well to various problems after reading it.The load capacity of goods and the tonnage of goods transported at once also affect the speed of lifting and lowering. Achieving the excellent value of the lifting platform for transporting goods is a guarantee of speed. If the weight is too heavy, it affects the speed. If the goods are too light, it also affects the normal transportation time.Fot,Although lifting cargo elevators have good safety,FotLogistics hydraulic lifting platform, in practical work if we do not pay attention to detailed maintenance, accidents may occur. Therefore, due to the influence of alternating loads such as impact and vibration, or factors such as heat and deformation, coupled with rapid wear and tear, it is easy to cause the previously fastened components of high-altitude work platform equipment such as mobile elevators to become loose.Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, add enough oil and clean the filter. The fuel supply pump has drawbacks: check or exchange the pump.