The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.Olanjestad,Identification method of galvanized pipeWhether I-section steel is ordinary or light due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.ShanLuo City,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.In order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.I-beam, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, the precision of seamless pipe is relatively low, and it is prone to uneven wall thickness,Olanjestad27SiMn large diameter seamless pipe, low surface luminosity and high customization cost. At the same time, some pits or black spots are easy to appear on the inner and outer surfaces. In addition to these, the seamless pipe manufacturer needs to carry out off-line processing for its detection, and its strength is relatively high, the pressure is high, and its advantages can be reflected in the material of mechanical structure. Seamless pipe can be divided into hot extrusion, hot rolling and cold rolling stainless steel pipe according to its rolling method. In addition, different elements can also be used for classification. The inner and outer surfaces of seamless pipes shall be free from chaps, folds, cracks cracks, scabs, delaminations and other defects. If these defects are to be removed, it is necessary to use machining. The removed seamless pipes shall not have negative deviation after the inner diameter is followed, If other minor surface defects with negative deviation cannot be removed, it is not a qualified product. The allowable depth diameter of straight path of seamless pipe is less than or equal to mm, and its depth shall not be greater than . mm.Plan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio), the solution temperature is ~ ℃, and the solution time is min.Quality inspection report,The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test,Olanjestad8-inch welded pipe, more than one meter, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.

H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.How much does it cost?,I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, greatly accelerate the construction speed of the project and shorten the construction period.Effect of trace elements on properties of galvanized pipeApplication characteristics of I-beam:Olanjestad,Welded steel pipes need to be processed through various processes before application. The heat treatment of welded steel pipes is a very important link in the processing of welded steel pipes. Hot working is a metal hot working process in which metal materials are heated,OlanjestadAlloy tube 40Cr, insulated and cooled in a certain medium, and their metal properties are controlled by changing the metallographic structure on the surface or inside of the material. During the heating and cooling process of structural welded steel pipe workpiece, due to the inconsistency of cooling speed and time between the surface and the core, the temperature difference will be formed, which will lead to uneven volume expansion and contraction and produce stress, thermal stress.What is the purpose of flat steelKey technical characteristics of alloy pipe