including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Santiago de Maria,The third is the welding machine, which must ensure reliable performance and meet the process needs; The welding machine must have qualified ammeter and voltmeter to ensure the correct implementation of welding process. The welding cable shall not be too long, and the welding parameters shall be adjusted when it is too long.The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.San Pedro de Lloc,Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materialsWhen we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.

I-beam: national standard * what is the wall thickness of I-beamThere are five main guarantee measures for steel pipe welding. If these five aspects are guaranteed, the quality of galvanized pipe can also be guaranteed.→ compared with the concrete structure, the I-steel structure can increase the service area by %, reduce the self weight of the structure by % - %, and reduce the structural design internal force.Quality inspection report,The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, so it has excellent rolling fatigue characteristics and corrosion resistance. Therefore and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.The alloy tube can be hardened by induction heating, this kind of steel has been widely used as the material of rolling mill flap ball screw in rolling mill manufacturers. In addition to the excellent properties of cronidur steel, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment, and its application range is expected to be further expanded.The delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.

H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.ranking,Last week, the billet in North China market showed a slight rebound trend. The billet quotation in Tangshan, the leading city, rose first and then stabilized in four trading days, although the phase snail is still running at a low level, due to the small billet resources in the market, the steel mills unexpectedly rose, and the billet market rebounded. However, due to the continuous increase of capital pressure and the downturn in the transaction of downstream finished materials, the steel plant has always maintained a cautious wait-and-see attitude to maintain stability.The two ends of the steel produced by the seamless pipe manufacturer shall be cut into right angles, and the burrs on the surface shall be removed, which is the raw material used by the seamless pipe manufacturer. The embryo prototube embryo needs to be cut by a cutting machine to form an embryo material with a length of about one meter, which is sent to the furnace for heating through the conveyor belt. The billet is sent to the furnace. After internal heating,Santiago de MariaI-beam customized architectural I-beam, the temperature is about degrees and the fuel used is often ethyne. Temperature control in the furnace is a very key factor.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology,Santiago de MariaHow much is 80 welded pipe per meter, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm which exceeds the welded composite section.Santiago de Maria,Santiago de MariaHow much is the I-beam of 16,Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.