Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.Auckland,Auckland16 square tube,There are many forms of heating furnace, but the ring heating furnace is mainly used. The heating furnace has an annular furnace bottom, which can rotate slowly, the blank is loaded along the diameter direction of the furnace bottom from the inlet, and the heating operation especially needs patience. Because if the heating operation is not standardized, cracks, folding and eccentricity on the inner or outer surface of the tube blank will only produce waste products and defective products.Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.Kerkera,The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.After spraying (throwing) derusting it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).

Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.The common surface treatment of square pipe includes surface treatment, chemical treatment, shot blasting treatment, manual mechanical treatment and flame treatment. The treated will be separated. ~ Mpa compressed air entrains abrasives, and the nozzle sprays to the steel surface at high speed. The impact and friction of abrasives remove the oxide scale, rust and dirt on the steel surface, and make the steel surface reach a certain roughness.The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore it can only be used as an auxiliary means in production.Quality inspection report,The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes,AucklandGanzhou galvanized pipe, seamless square tubes,AucklandGalvanized square pipe, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.

Square tubes for low and medium pressure boilers (gb-) are high-quality carbon structural steel hot-rolled and cold drawn (rolled) square tubes for superheated steam tubes, boiling water tubes for low and medium pressure boilers of various structures and superheated steam tubes, small smoke tubes and arch brick tubes for locomotive boilers. Square tubes for high-pressure boilers (gb- is a high-quality carbon steel, alloy steel and stainless heat-resistant steel square tube for the heating surface of water tube boilers with high pressure and above. High pressure square tube for chemical fertilizer equipment (GB - is a high-quality carbon structural steel and alloy steel square tube suitable for chemical equipment and pipelines with working temperature of - ~ ℃ and working pressure of ~ mA.Respect for customers,Generally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, its anchor lines are shallow and easy to pollute the environment.At the same time, the heating temperature and heating time will also have a great impact on the performance of square tube. The heating of square tube blank is the key process to ensure that the square tube blank has enough plasticity and complete the smooth perforation. If the heating temperature is too high or the heating time is too long, the billet of the square tube will be burned and decarburized, and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Auckland,For structure: as pile driving pipe and bridge; pipe for wharf, road and building structure, marine pile driving pipe, etc.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionB. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)