B. spring steel C. bearing steel tool steel: A. carbon tool steel; b. Alloy tool steel; c. High speed tool steel.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Alajuelita,High temperature diffusion heat treatment of ingot can improve the composition heterogeneity of ingot and improve the transverse performance of square tube.Ferroalloy is an alloy composed of iron and silicon, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.MaladzyechnaSquare tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.

According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.According to the welding specification, it is determined that the butt weld of QB square pipe adopts double-layer CO gas shielded welding. HMnSiA, mm welding wire for welding material; The shielding gas is pure CO gas. The welding current of layer weld is ~ A, and that of the second layer is ~ A; The arc voltage is ~ V. The process requirement is that the layer weld must be fully welded to ensure good back forming; The welding current, wire feeding speed and welding speed can be adjusted according to the equipment model.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.High quality brand,The second is the pickling of the square pipe. Both chemical and electrolytic methods are used when pickling the square pipe. These two methods can remove the oxide skin of the square pipe.During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used,AlajuelitaGalvanized thin-walled rectangular tube, the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.

Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.knowledge,There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, I'll give you a detailed introduction to the heating technology of the lower tubes.With the development of economy,AlajuelitaPVC galvanized steel pipe, there are a lot of demands for project construction, which leads to the continuous increase of square pipe. The of square pipe is more complex. Great efforts should be made in the selection of raw materials, structured treatment and so on.Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Alajuelita,Qb square tube, qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same,Alajuelita50 galvanized square pipe, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.Forging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.