After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore,Bosanska Gradiska200 galvanized pipe, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.Bosanska Gradiska, Standard No.: gbt-. The representative materials are the same as above. It is mainly used to transport low-pressure fluids such as water, gas, air and oil and add water or steam. The surface of square pipe shall be hot galvanized or cold galvanized.Stage ( & mdash; )Mendip, chemical and electrolytic methods are usedPlasticity QB square plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.

High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.How to reduce the amount of oxide scale is the key to the heating operation of seamless square tube. Especially when it's hot. Starting from the service life of tools and the surface quality of pipes, the requirements are more stringent. For example, hot furnaces are divided into heating furnace and reheating furnace according to their functions; The former is used to heat the blank from normal temperature to processing temperature; The latter is used to reheat the blank to the necessary processing temperature during processing.Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.original,Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!Generally speaking, square pipe welding has a process: ignition, pressurization and thermal insulation.B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.

Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.Market trend,The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.The welded joints of square pipes are subject to on-line continuous ultrasonic automatic flaw detector to ensure the NDT coverage of spiral welds. If there are defects, it will automatically alarm and spray marks. The production will adjust the process parameters at any time to eliminate the defects in time.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.Bosanska Gradiska,Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Forging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.