The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Perugia,Any product always has a running-in period when it is used for the first time, so what should we pay attention to during the running-in period of using the hydraulic lifting platform? Today, the editor will share this topic with you.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Kurashiki, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, and in severe cases, the winding will be burned.

Hydraulic system: mainly oil cylinders,PerugiaTwo ton lifting cargo elevator, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations oil pipelines, solenoid valves gear pumps etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Keep external construction liftingThe approach road is smooth and there is enough space for parking equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Quality assurance,The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, the three-phase current will be unbalanced and the motor will overheat.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.

The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Highly recommended,Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Function: Convenient unloading, strong stability, low maintenance cost. It is suitable for various vehicles on the loading and unloading yard and places with relatively heavy traffic. Loading and unloading platform, lifting platform, which can realize the anti-slip function efficiently and is reliable.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Perugia,If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt,PerugiaCustomized lifting cargo elevator,PerugiaCargo elevator, it must be washed off with gasoline or thinner.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.