The third is color.Some customers are very strict about the color of the floor and must maintain the same color difference.But this provision is unscientific.Because the wood is affected by the sun, raw material parts, growth and development parts and lower sawing points, it will inevitably cause inconsistent color difference.Fifth, smell with your nose is not protected by the environment.ViennaBaden, Technical floor repair wax.Prepare the floor for hardwood installationDubai,Improve the sense of hierarchy, reliability and cost performance of the floor. Why don&#;t the community owners choose the solid wood floor?sound insulationImprove the sense of hierarchy, reliability and cost performance of the floor. Why don&#;t the community owners choose the solid wood floor?

Fire protection, fire rating B, second only to stone.In another case, the scar is deep, which can be supplemented with solid recovery wax, colored with paint repair pen, and then polished.When assembling the solid wood floor, do not be too loose or too tight.The assembly relaxation shall be reasonably arranged according to the temperature of the indoor environment. The assembly relaxation will produce a large gap with the shrinkage of the floor.The assembly is too tight and the floor is arched when it expands.Click to view, and a certain number of wear-resistant revolutions corresponds to a certain content of aluminum oxide.For household floors, the number of wear-resistant revolutions is usually more than revolutions,ViennaBadenMultilayer solid wood composite floor, while in public places, it is usually more than revolutions. You can buy it on demand.As mentioned above, calcium powder has good thermal conductivity, so paving the floor at home is the best choice. Even if it gets hot, it will not release harmful gases.SPC floor is a new type of floor, also known as stone plastic floor. Its base material is a composite plate made of stone powder and thermoplastic polymer, which is stirred evenly and extruded at high temperature. At the same time, it has the characteristics of wood and plastic to ensure the strength and toughness of the floor.How to lay lacquer cloth?The construction procedures and methods are as follows: first, measure the structural size of the room accurately;Then cut the lacquer cloth according to the size.Note that the cutting width should be slightly larger than the required width to facilitate overlapping,ViennaBadenHow about floor leather, matching and trimming during paving.The cut floor paint cloth shall be placed at room temperature of no less than ℃ for about hours, so that the crimped part of the floor paint cloth can be fully extended and ready for the final paving.Special adhesive shall be used for paving the floor paint cloth.Before paving, the indoor ground shall be treated first.

Common types: three-layer solid wood composite floor, double-layer solid wood composite floor, new solid wood composite board.quality,Advantages: it is warm for many days and cool in summer. Of course, so there are no indoor formaldehyde, benzene and other harmful substances.The indoor formaldehyde emerald green floor is not easy to cause damage to the body.The main raw material of SPC floor is polyvinyl chloride. Polyvinyl chloride is an environment-friendly, non-toxic and renewable resource. It has been widely used in people&#;s daily life, such as tableware and medical infusion pipe bags. Its environmental protection does not need to be worried.SPC floor (sheet) is mainly composed of natural stone powder,The third kind: you can smell the faint smell of wood. This floor shows that there is little glue content.It can reach European standard E level Main performance.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat clean and dry, and the tool shall be a toothed rubber scraper.During gluing it can be glued and paved.Gluing is the last process before paving, glue shall be applied on the ground according to the size of the floor paint cloth and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, it can be paved. When pasting, pay attention to aligning the sidelines and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile,ViennaBadenHow about composite floor, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.