SPC floor has special anti-skid property. The more it meets water, the more astringent it is. Even if you wear running shoes with nails, you won&#;t leave scratches on the floor.If not, then you may need to do a lot of work: there are some interesting surprises lurking under the old floor.When installing laminate flooring, workers must be very careful to complete qualified work.Multilayer carpets or vinyl can be difficult to move and are usually much heavier than they look!After removing the old floor, it is necessary to ensure that the floor is level and in good condition before installation can begin.Similarly, experienced hardwood flooring installation experts can solve this problem for you to ensure that the new flooring has perfect smoothness and levelness.For more convenient tips, please check our hardwood flooring installation guide.Tips for preparing the house before floor installationManati, Select water resistance.Some people say this method is unscientific and laminate flooring can&#;t soak in water, but I have done some experiments and come to another conclusion.Arecibo, Keep the floor dry and clean. If there is dirt on the floor surface, generally wipe it dry with a damp mop without dripping water. Select substrate densityIn addition,ManatiTunnel waterproof board, pay attention to whether there are sawdust and stratification on the cutting surface of the plate and whether there are sawdust and stratification on the cutting surface of the solid wood floor.

The current woodworking is basically done by woodworkers. The 'general woodworking' method is adopted, and the shrinkage joint size is not calculated according to the thermal expansion and cold contraction parameters provided by SPC flooring factory.If the room is slightly larger, but the reserved gap is too small, especially when the temperature difference between winter and summer is too large, it is very easy to have no gap to expand, resulting in arching and warping.It is not easy to deform and crack, and the dry shrinkage expansion system is very small. It has a good ability to adjust indoor temperature and humidity. The surface layer can show the natural wood grain of wood. The pavement is simple and has a wide range of application.The price is higher than composite flooring and lower than solid wood flooring.It is suitable for installing geothermal heating room. Generally, wear-resistant paper with aluminum oxide content of about g / m is used, or wear-resistant paper is not used.Low density board (medium density board is rarely used), and the number of wear-resistant revolutions is usually between - revolutions.The edges and corners will be worn after being used for one or two years at most.With Hunan Hubei, Liaoning Jilin and Heilongjiang as the gathering points, the suburbs of Beijing are still rampant.Low quality, not environmental protection, government departments are strictly investigating and dealing with it.Such illegal businesses only take into account short-term interests and have no after-sales service guarantee. The price ranges from to yuan.Variable cost,ManatiEffect drawing of laminate floor,In addition to the high wear-resistant solid wood floor, the electronic organ architectural coating floor is also the main product in the recent popular sales market.Beautiful and bright appearance, with super thick wear-resistant layer, the actual effect is brighter and deeper, and the upper foot is stronger. The appearance is very similar to the solid wood floor,ManatiColor collection of laminate flooring, but the price is far less than the solid wood floor.The solid wood composite floor is overlapped and laminated by the boards of different greening plants, which gets rid of the defects of wet expansion and contraction of the solid wood floor to a certain extent. The dry shrinkage and wet expansion rate is small, the specification stability is good, and the wood texture and comfortable feet of the solid wood floor are preserved.The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary the cost is much higher if the number of wear-resistant revolutions is high. Domestic cheap decorative paper is usually used. The pattern of this decorative paper is fuzzy. The biggest defect is that it is generally not UV resistant and will fade after sunlight.This is why some consumers reflect the discoloration of the places near the balcony and windows three or four months after the floor is installed. The base material is poor, medium and low density board or particleboard is used, the quality index is unstable, and the formaldehyde seriously exceeds the standard.

The machining accuracy is poor, and it is often claimed that it is: imported large plate and domestic slotting.Product survey,The third kind: you can smell the faint smell of wood. This floor shows that there is little glue content.It can reach European standard E levelConsidering the Japanese style of the family, plus the all-round shops in the living room and restaurant, the color needs to be light color light yellow, moderate stability, and the preliminary positioning of white oak. The reinforced composite wood floor has the texture of natural wood floor at the same time, and the price is reasonable, which is favored by the majority of consumers. However, many consumers are worried that formaldehyde will be stored in the production and processing process of composite floorIn, it is harmful to human body. How about using reinforced composite wood flooring? What are the advantages and disadvantages of reinforced composite wood flooring? Let&#;s take you to know about the relevant situation of reinforced composite wood flooring and have a look together.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of : leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Manati, hospitals, studies, office buildings, factories, supermarkets, businesses, gymnasiums and other places.SPC floor is mainly composed of a certain proportion of calcium powder and PVC stabilizer to form a composite floor paving material.It is a new material invented in response to national emission reduction, hard SPC indoor floor.SPC floor takes calcium powder as the main raw material. After plasticizing and extruding sheet, four roll calendering hot compress color film decorative layer and wear-resistant layer, while SPC boards range from to mm.