Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?　　Many users,St Lucas tolimanSewage pump diving, including new practitioners of slurry pumps often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?St Lucas toliman,　　 Constantly observe the instrument, check the electrical equipment, and measure the insulation resistance every half a month. The resistance value shall not be less than . megohm.　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.Shenzhen City,　　Third, the whole industrial and mining system operates stably, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　So it is called: submersible slurry pump.

　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, carefully check whether the cable is damaged,St Lucas tolimanRubber lining submerged slurry pump, whether the fasteners are loose or fall off, and whether the pump is deformed or damaged during transportation,St Lucas tolimanSubmersible non clogging slurry pump, storage and installation.　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.production,　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated power　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.　　 Then reinstall the equipment on the engine and install the rubber hose.

　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Development Curriculum,　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　The water pump is not installed firmly or installed too high.　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchangedSt Lucas toliman,　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation seawater lifting, ship load adjustment, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes etc. Submersible pump is generally divided into clean water submersible　　In fact, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)