Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　Water pump After understanding the cause of insufficient liquid supply we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Sanarat,　　In fact, stainless steel is not only advocated in the medical industry, but also widely used in the water pump industry. The stainless steel submersible pump of denang pump is one of them.　　Third,SanaratDouble suction slurry pump, the whole industrial and mining system operates stably,　　When in use, it can drive the impeller to rotate so as to drive it to flow.　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.

　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.　　 Pipeline high-temperature oil pump, pipeline high-temperature chemical pump, pipeline high-temperature hot water pump. These models are designed to be formed on the basis of adding water cooling units, and the operating temperature can be as high as degrees or higher.　　Work, no noise and vibration, and the site is cleaner.Where to sell API,SanaratPipeline pump body, it can transport the slurry and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.

　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.Range　　Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning,SanaratVertical centrifugal slurry pump, and the consequences will be unimaginable.　　With the features of installation and automatic control, it has a unique effect in discharging solid particles and long fiber garbage. For example, the common rexwell WQ series submersible sewage pump with runner impeller structure has good over-current performance, which can effectively reduce blocking and winding faults and greatly improve　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.Sanarat,　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, and the submersible slurry pump can supplement this part of the blank work point.　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?