Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe,South San RafaelGalvanized square pipe production line equipment, spiral weldingSouth San Rafael,The researcher's test before using the strip thinning drawing also confirmed that using the strip thinning drawing can greatly reduce the large value of tangential residual stress of the drawn parts and effectively prevent the occurrence of longitudinal cracking. According to different deformation degree and original sheet thickness, if & psi; If n is too small, the deformation stress will increase sharply, resulting in the fracture of the bottom of the drawing part.The first is to remove the rust of the square tube. When removing the rust of the square tube, the steel wire brush is mainly used to polish its surface, which can effectively remove the loose or rusty rust on the surface of the square tube.Rosiori de Vede,The load of impact toughness acting on the parts at a great speed is called impact load. It is specialized in products and renewable resources. Its business includes: square tube, square tube, seamless square tube, galvanized square tube and galvanized tube. The ability of metal under impact load is called impact toughness.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.During the pushing process of spot welding and repair welding elbows, there will be thinning so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used, the thickness is significantly lower than the standard.

Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.After chemical treatment and surface treatment of the square tube, the appearance and quality of the square tube have been improved to another height, making the current square tube present in the market in a good state.Brinell hardness (HB) Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.analysis,Purpose of square tube the purpose of square tube includes construction, solar power generation support shipbuilding steel construction and other projects, electric products ( pieces)Cleaning solvent and emulsion can clean the surface of square tube to remove oil, grease, dust, agent and similar organic matter, but it can not remove rust, scale, welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.

If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Latest consultation,The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes,South San RafaelWhich is a good galvanized round pipe, on-site settlement, honest operation,South San Rafael125 galvanized welded pipe, local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.Shot blasting is commonly used to clean the surface of castings or strengthen the surface of square tubes.Stage ( & mdash; )South San Rafael,So flat, and the size and thickness are not standardized, it can reflect that this square tube is a poor product& rdquo;Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.B. spring steel C. bearing steel tool steel: A. carbon tool steel; b. Alloy tool steel; c. High speed tool steel.