Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, phosphorus P and chromium CR.Delgado,At the same time, the heating temperature and heating time will also have a great impact on the performance of square tube. The heating of square tube blank is the key process to ensure that the square tube blank has enough plasticity and complete the smooth perforation. If the heating temperature is too high or the heating time is too long, the billet of the square tube will be burned and decarburized, and even the chemical composition of the square tube will be unqualified (unqualified carbon content), which is easy to cause batch quality problems and seriously affect the product qualification rate.The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials,According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!

Product description of square tube square tube is a light thin-walled steel tube with hollow square section,DelgadoGalvanized layer thickness of square pipe, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance and good low temperature toughness.During the storage of square tubes, pay attention to the stacking layers of square tubes to avoid local stress at the tube end caused by too many layers, resulting in radial plastic deformation and layer damage of square tubes. It is recommended that the stacking layers of smooth pipes refer to apirp l- Recommended Practice for railway transportation of square pipes for pipelines or apirp lw- Recommended Practice for ship and sea vessel transportation of square pipes for pipelines. It can also be determined by test or implemented according to the safe stacking height of square pipes. The stacking layers of pipes shall be implemented according to GBT - polyethylene layer of buried steel pipelines.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.reform,DelgadoOf hot dip galvanized square pipe,Stage ( & mdash; )The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement, honest operation, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.Functional index analysis of qb square tube - the load on the machine parts due to the great progress of strength is called the frontal collapse load. The power of destruction of qb square tube under the frontal collapse load is called the frontal collapse toughness.

For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.Application process,The surface of galvanized square pipe treated by sand blasting,DelgadoDN25 galvanized water pipe, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.The square tube can be sprayed with fluorocarbon paint, which needs some treatment before spraying.Hundreds of degrees Celsius, which can save energy.Delgado,Put the pig iron for steelmaking into the steelmaking furnace according to the specified process to obtain steel. The products of steel include ingots, continuous casting billets and various steel castings made of straight square tubes. Generally speaking steel refers to the steel rolled into various square tubes. Square tube steel belongs to ferrous metal, but steel is not completely equal to ferrous metal.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , plates and tubes. It is divided into cold rolling and hot rolling.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.