The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence villa water supply, water supply system factory water supply, drinking water system and water treatment. In short, there are many uses.Irapato,　　 Check the current, voltage and outlet pressure every day,　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　In this way, when the equipment is used again, the solvent in the pump is often less,IrapatoAh slurry pump,IrapatoSubmersible sewage pump, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.

　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　Select an appropriate flow according to the water inflow of the well or pool or the water consumption required by the actual engineering system. During model selection, the flow shall be close to the model flow grade of the sample (to ensure that the pump operates in the high efficiency zone).　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.Packaging strategy,　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation, the motor shaft drives the water pump impeller to rotate, and transmits energy to the slurry medium to generate a certain flow rate, drive the solid flow, and realize the transportation of slurry.

　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.production,　　Many users, including new practitioners of slurry pumps, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　Fiber rope. Perform maintenance, replace new bearings and remove debris. In addition, the liquid may corrode the mechanical seal of the submersible pump or the pump body, causing water to enter the submersible pump motor and damaging the submersible pump motor. The effect of using sewage electric pump is good.　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition,IrapatoHorizontal wear-resistant slurry pump, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local placesIrapato,　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, etc. Submersible slurry pump blade