It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф . Anchor bolt structure for M assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. The platform is based on&quo; U” Shaped steel as the skeleton with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of kilometers/hour when the forklift is fully loaded without bending, and all equipment can provide good anti slip characteristics to a certain level in operation and application. The hydraulic press loading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods. Its height adjustment function creates a bridge between the large truck and the cargo platform in the warehouse. Transport vehicles such as electric forklifts can immediately enter the large truck to carry out mass loading and unloading of goods, also known as the loading and unloading service platform. That way, the device can loosen the return valve button during the lowering process thereby reducing the weight of the device.Pumacil,Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage,PumacilHydraulic mobile boarding bridge, it is necessary to check the oil level in the housing, if there is insufficient oil, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely mannerVibration acoustic method: Vibration acoustic instruments detect the vibration and noise of hydraulic systems and identify the wear (a basic type of component failure) and technical status of hydraulic components according to the laws of vibration acoustics. Based on this, diagnose the cause, location, degree, nature, and development trend of faults. Nowadays, with the rapid development of the logistics industry the demand for logistics equipment is becoming increasingly weak, and auxiliary improvements such as fixed hydraulic boarding bridges and fixed lifting channels,PumacilHydraulic lifting mobile boarding bridge, as well as the increase in loading and unloading equipment usage,With the listing of Alibaba Group on the New York Stock Exchange in the United States, it will also have a significant impact on the development of the entire internet and logistics industry. The valuation is as high as billion US dollars! The professional boarding bridge factory and other various types of products have a complete range, welcome to inquireIn general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.Both electric lifting and manual lifting and lowering use manual pump switch to return.

The anti slip device of the auxiliary equipment for loading, unloading, and handling of goods applied: This equipment is made of thick steel plate welded by electric welding, which can reasonably maintain the anti slip effect and can be trusted. It is a long-term operating boarding bridge factory. Welcome to inquireActivate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time, release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed, the operation can begin. After waiting for the homework to be completed, press the up button to drive the vehicle away. Release the button panel and it will automatically descend to its original state, parallel to the cargo platform.In general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.Where to sell API,The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixedAnti collision block: This device can effectively protect buildings and boarding bridges from damage.The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.

　　. Platform side boarding bridge: The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages.Interpretation and observation, as the fixed hydraulic boarding bridge is used to complete the rapid loading and unloading of goods through height adjustment plates,PumacilMovable hydraulic boarding bridge, there are certain strict requirements for the quality and material selection of height adjustment plates to avoid the occurrence of defective materials, which will result in unexpected loss of performance in the application process.Adopting imported integrated modular hydraulic station, with good sealing performance and long service life.Hydraulic boarding bridges can reduce economic and component costs to a certain extent. In the process of applying mechanical equipment, unexpected common faults may sometimes occur, which may lead to safety accidents. In fact, such devices themselves will also be equipped with certain security protection.Pumacil,The anti slip device of the auxiliary equipment for loading, unloading, and handling of goods applied: This equipment is made of thick steel plate welded by electric welding, which can reasonably maintain the anti slip effect and can be trusted. It is a long-term operating boarding bridge factory. Welcome to inquireThe fixed boarding bridge of the service platform is immediately installed on the outer edge of the unloaded service platform during the entire installation process. When applied, there is no need to excavate or pre bury the indoor space of tunnel construction on the loading and unloading platform, and most of the buildings do not need to be modified in terms of structure.Secondly, the selection of hydraulic pump stations and oil cylinders for fixed hydraulic boarding bridges is also crucial. These equipment are central components of external equipment and cannot be ignored. This not only determines the long-term use of fixed hydraulic boarding bridges, but also the inability to support the entire operation process!