it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Harlem ,Familiar with the use process and there is no doubt that this is the first to bear the brunt. There are two ways to understand the content that needs to be understood: one is the instruction manual provided by the manufacturer when the hydraulic lifting platform leaves the factory, which needs to be read carefully; the other is the equipment to be installed, hydraulic The lifting platform will send a professional installer to install it, and after the installation is completed, the relevant users will be trained on the operation process and safety precautions of the hydraulic lifting platform, and some matters for future maintenance will also be explained; the running-in period of the hydraulic lifting platform What items should be paid attention to Check the wear of parts Newly processed and assembled parts have subtle deviations in shape and size and need a period of running-in. During the running-in period attention needs to be paid to whether there is excessive wear and tear. High prices and various specifications Freight elevator factory has timely supply and high cost performance. It has become the preferred brand of many wire products. Welcome to buy! If you haveThe manufacturer handles it to avoid equipment failure; work between the pins and bearings to ensure that, to avoid wear, you can add some oil or butter; confirm whether there is noise. During the running-in period, it is found that the hydraulic lifting platform has noise during operation You don’t have to worry about it in the early stage. If there is no major problem, the noise will naturally disappear. But if there is noise for a long time and there is no sign of fading, please be sure to solve it by the manufacturer in time; check the parts regularly Check whether it is loose before use, whether there are any signs of looseness in the screws, nuts, retaining springs, backstops, oil pipe joints, etc. If there is any sign of looseness, please reinforce or replace it in time to avoid accidents.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation,The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore,Harlem Simple lifting cargo elevator for factory building, you must ask whether the manufacturer has these two certificates.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.

Before the elevator manufacturer connects the motor to the elevator please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?For the daily maintenance of the rail-type elevator, it is necessary to add butter twice a month to the general transmission position where the grease fitting is located. For the parts that cannot be filled with butter, it is necessary to clear the oil circuit or replace the grease fitting until the butter can be added. Otherwise use of the device is prohibited.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.market,Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, old brand price advantage, quality guaranteed!Professional is king,Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.Integrity of the overall structure Check whether the overall structure is deformed and whether important parts are damaged, especially the load-bearing poles and chains.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Harlem ,Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force,Harlem Heavy industry guide rail type cargo elevator, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.