The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.corner,How to specify the yield point of square tube: if the stress decreases, the upper and lower yield points shall be distinguished. The unit of yield point is nmm (MPA). Upper yield pointChange to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )Picsi,Among them, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral weldingC. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.

special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workIt is learned from the authority that if there is dirt on the outer surface of the square pipe during degreasing,cornerPrice of 1-inch galvanized square pipe, it can be washed with purified water and dried naturally, then soaked with degreasing agent with a dry cloth to remove the oil, and then dried in the open air. When degreasing the inner surface of the opposite pipe the end of the pipe can be tightly blocked with a wooden plug or closed with other. The degreasing solvent with the volume of % - % of the pipe from the other end shall be sealed with a wooden plug, placed in a flat and clean place or on a workbench with sleepers for -min,corner350 galvanized square pipe, and the pipe shall be rotated every min. If degreasing is required for stainless steel elbow, degreasing solvent shall be appropriately added to make it fully soaked. After degreasing, pour out the solvent in the pipe,cornerPrice of 1-inch galvanized water pipe, dry the pipe with exhaust fan, or dry it with oil-free compressed air or nitrogen, or dry it with natural air. Large diameter pipes can be manually scrubbed with cotton cloth dipped in solvent; The square tube can also be soaked in a long tank containing solvent for to minutes. The concentrated pipeline and equipment of the concentrated unit can be directly pumped and circulated with % concentrated for pickling after all installation. Pipes that cannot circulate or are not resistant to concentrated corrosion must be degreased separately.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.How many?,If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.For improper stamping direction, simulation software shall be used in the initial stage of design to ensure that the direction of stamping parts is analyzed, and when the high-quality requirements of components require the re development of molds, the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming, bending and bending of square tubes. As the name suggests, the bending is compacted and the inner and outer rollers are double with the inner and outer walls of tube billets during actual bending Compact towards the.

High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.How many?,Functional index analysis of qb square tube - the load on the machine parts due to the great progress of strength is called the frontal collapse load. The power of destruction of qb square tube under the frontal collapse load is called the frontal collapse toughness.The covering shall be strong and durable to prevent decay and leakage caused by long-term sun and rain.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.corner,Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionC. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.The reason why it is divided into two types is that chemical cleaning can only clean the surface very thoroughly and it is difficult to achieve the desired results in some fine cracks.