Methods of exerting efficiency in application of C-section steelStages needing attention in the production and manufacture of alloy tubesQuebec,Recently, the price of zinc has been falling continuously. The key reason lies in the soft skin of galvanized pipe consumption and the slow start of production and marketing rate of manufacturing industries in the middle and lower reaches after the Spring Festival. The disadvantage of zinc price has long been far beyond the level of cyclical factors. The main performance of no prosperity in the hot season is whether the market situation in the off peak season will become a more worried problem in the galvanized pipe sales market.The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Leshu,QuebecHow much is the I-beam per ton,QuebecGH3044 superalloy tube,Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.

The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Cutting machine, polishing machine, electric hammer, etc The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.analysis,The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.Passivation treatment operation of alloy pipe

Performance parameters and application scope of I-beamQuality assurance,I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period. Quality requirementsWhen selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties chemical properties, can be accurately positionedC - section steel is reliable and stable in stress, it has good versatility and combination and has a variety of C-section steel and size selection to ensure its flexibilityThe import and export order of I-beam is generally based on the specifications required in use after determining the corresponding carbon structure steel (or low alloy steel) steel grade. Except for the specification number, I-beam has no specific composition and performance series.I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.