ArcaiCorrosive pipeline pumpSteps of protective construction
2023-08-21 10:07:46Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it. Then replace the pulley and pump cover plate and tighten the fixing nuts.Arcai, Realize centralized management. In the application of multiple fire pumps the deployment of fire pumps may be decentralized, and the working environment of fire pumps is often complex, with operation Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you should find a professionalDayr al Balah, If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damaged Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles. The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.
Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump,ArcaiCirculating hot water pipeline pump,ArcaiScrew deep well pump,ArcaiVertical slurry pump, because the current sealing technology in China is more than meters, but because within the estimated installation depth, the minimum inner diameter of the well is mm To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses. in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate. If the oil seal ring of the shaft is seriously worn, replace it with a new one.
Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press theWorkshop cost, It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators Attachment: data sheet required for ordering deep well pump Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pumpArcai, In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump, submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor and Promote the continuous expansion of the sales network group.