There are various connection modes of stainless steel pipes. The common types of pipe fittings are compression type, compression type, union type, push type, push thread type, socket welding type union flange connection, welding type and derivative series connection mode combining welding with traditional connection. These connection modes have different application ranges according to their principles, but most of them are easy to install, firm and reliable. The sealing ring or gasket materials used for connection are mostly silicone rubber, nitrile rubber and EPDM that meet the requirements of national standards. L stainless steel pipe, s stainless steel pipe, L stainless steel pipe and other brand products are provided for a long time. The designated products are complete and the quality is guaranteed, which eliminates the need for use Series & mdash; Martensitic precipitation hardening stainless steel.Saint-Louis,Ti-a alloy with improved titanium and overall corrosion resistance has been used to manufacture u and Pu solution evaporation boilers and heat recovery evaporation boilers in Donghai reprocessing plant, Japan. In addition because zirconium has stable corrosion resistance in the environment, zirconium is used in its continuous dissolution tank in the reprocessing plant in liusuo village, Aomori County, Japan. The US Academy's ruling that the countervailing duty is not suitable for products from non market economy countries has just given China's steel pipe enterprises a little relief. The anti-dumping stick from the EU has given a heavy blow to hundreds of domestic stainless steel pipe manufacturers.Austenitic stainless steel. It contains more than % chromium, about % nickel and a small amount of molybdenum, titanium, nitrogen and other elements. Good comprehensive performance and resistance to corrosion of various media.Droichead Nua,Model & mdash; The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.When using this process, the following key points should be paid attention to: during the welding process,Saint-LouisStainless steel plate and strip, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;,Saint-Louis904L plate stainless steel, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.When water-soluble paper is used to block the ventilation, due to the ventilation from the weld center, the ventilation pipe shall be pulled out quickly at the later sealing link, and the residual argon inside shall be used for protection, so as to quickly finish the bottom and seal the mouth.

Marking: in order to make the steel pipe complete the socket of the pipe fitting, the length must be marked and marked at the pipe end.In addition, when selecting the reasonable thickness of the steel plate, its service time, quality and stiffness should be considered, and the strength requirements of the plate under pressure should be considered; Thermal conductivity; Distribution of pressure and format specification of pressing plate.Editor's note on the causes of steel rusting: chloride ions exist widely, such as salt, sweat stains, seawater, sea breeze, soil, etc. stainless steel corrodes rapidly in the presence of chloride ions, even surpassing ordinary low-carbon steel. Chloride ions form complexes with Fe in alloy elements, reducing the positive potential of Fe, low-temperature equipment components in refrigeration industryAustenitic stainless steel is generally used for manufacturing and manufacturing chemical equipment components, and can be used as stainless steel spring and clock spring after deformation strengthening.When water-soluble paper is used to block the ventilation, due to the ventilation from the weld center, the ventilation pipe shall be pulled out quickly at the later sealing link, and the residual argon inside shall be used for protection, so as to quickly finish the bottom and seal the mouth.According to the purpose, it can be divided into oil well pipe (casing, oil pipe and drill pipe), pipeline pipe, boiler pipe, mechanical structure pipe, hydraulic prop pipe, gas cylinder pipe,Saint-Louis304 stainless steel with magnetic, geological pipe, petroleum cracking pipe) and marine pipe.

Stainless steel is usually divided into stainless steel pipe, toughness and weldability increase with the increase of chromium content, and its chloride stress corrosion resistance is better than other kinds of stainless steel.equipment maintenance ,When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.Hydraulic saw grinding disc (manual saw wire cutting machine). Series & mdash; martensitic precipitation hardening stainless steel pipe.Saint-Louis,Stainless steel export is an important part of China's export economy. It plays an important role in stimulating China's economic growth. However, China's stainless steel export has encountered great resistance.Stress corrosion cracking (SCC) refers to the cracking caused by the combined action of stress corrosion stress (mainly tensile stress) and corrosion of austenitic stainless steel Austenitic stainless steel is prone to stress corrosion in corrosive media containing chloride ions. When the Ni content reaches % - % it is a long-term enterprise engaged in stainless steel plate, stainless steel coil stainless steel belt and stainless steel pipe. Welcome to consult. The stress corrosion tendency of austenitic stainless steel is very large. Continue to increase the Ni content to ~ %, and the stress corrosion tendency gradually decreases until it disappears.It has the characteristics of high efficiency and low cost. At the same time, it can also well ensure the welding quality (in the capacity expansion and reconstruction project of Urumqi petrochemical, we use this method to weld joints and repair joints, with a one-time qualified rate of welding)