eliminate structural defects reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Generally, there are many passivation methods for alloy tubes, the common ones are high temperature passivation or sodium cyanide passivation.Mr. conjik, Steel mesh guardrail (steel mesh fence) steel mesh guardrail refers to the guardrail made of steel mesh. It is stronger and more durable than the guardrail made of electric welding mesh, steel mesh, hook mesh, but its cost is much higher, and it is rarely used under normal circumstances The defects can be removed by grinding with sand wheel,H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingI-beam is widely used in buildings or other metal structures.At the same height, light I-beam has narrower legs, thinner waist and lighter weight than ordinary I-beam. No. - is large I-beam, and No. - is medium I-beam. Imported I-beam shall be marked with actual specifications, dimensions and relevant standards.

I-beam is mainly divided into ordinary I-beam,Mr. conjikPrice quotation of second-hand I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.First, the wall thickness of high-quality and smooth steel is particularly thick. Because the thicker the wall thickness of the product, the higher the economy and practicability. The thinner the wall thickness, the greater the processing cost and opportunity, and the higher the resource cost. Secondly, the process of smooth steel also determines its limitations. Generally, smooth steel has low precision, low brightness inside and outside the pipe, high length cost,Mr. conjikWhere are many manufacturers of welded pipes, pockmarks in the internal appearance, and black spots are not easy to remove. Again, the inspection and shaping need to be processed offline. Therefore, it has its advantages in high pressure, high strength and mechanical structure materials. In the process of use, we will gradually find out. In fact, seamless pipe has also entered the market in recent years. With the growth of market demand, the advantages of seamless pipe have also been stimulated. But there are also many fakes and fake products on the market. Be careful when you choose.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Interpretation and observation,When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small) a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Stages needing attention in the production and manufacture of alloy tubes

The wear resistance fracture toughness, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test impact toughness and bending strength under different process conditions were compared, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Workshop cost,Application characteristics of I-beamExternal steel bonding reinforcement method is a more traditional reinforcement method. The utility model uses an adhesive to paste the steel plate or reinforcement mesh on the cracked part of the wall to achieve the purpose of reinforcement. The commonly used adhesive is usually epoxy resin. This method is simple and fast in construction and has little impact on production and life. Basically, the bearing capacity of the wall can be greatly improved without changing the shape and internal use space of the components. It is mainly applicable to the reinforcement of walls that do not allow to increase the section size of original components, but can greatly increase the section bearing capacity.The key purpose of grinding and polishing alloy pipe is to moisten the surface and the relevant limit accuracy or appearance change is not easy to change.Mr. conjik,The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.Defects of alloy pipe and solutions:I-beam, whether ordinary or light, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.