If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,TiranaSubmersible non clogging slurry pump,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it will not only easily corrode the parts　　The water pump is not installed firmly or installed too high.　　The non service life of the equipment is not as long as possible. If it is not used for a long time, but also reduce the service life of the parts.Milan,　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown,TiranaDrilling fluid slurry pump, it is necessary to prevent damage to flow passage components caused by water hammer.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.

　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is full　　D. G-type slurry pump is a single pump shell structure, that is, without lining light weight. The pump body, cover and impeller shall be made of strong wear-resistant high chromium alloy or wear-resistant alloy steel, and the hardness shall not be lower than hrc. The connection of pump body and pump cover adopts special clamping structure, and the pump outlet direction can be rotated freely,　　 First of all we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However,TiranaFire deep well pump, one of the media conveyed by sewage pumps maydevice management, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, anti-corrosion, derusting and oil removal' >

　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and writepacking,　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　 for new or replaced deep well submersible pumps, after hours of use, check whether the seal is good. In the future, check it once a month. At the same time, check whether the shielding sleeve between the motor rotor and stator is well sealed. Try to reduce the number of starts in use.　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.Tirana,　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.