If the corrosion on the copper surface is found to be slight, it can be erased with linen copper wire, but it is not recommended to apply oil for preservation.Remove the flame. If the filler metal does not melt, continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe, the welding flux must have a degree of corrosivity, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.Weige,Finished products must be stored indoors. During storage, they should be protected from direct sunlight to the copper tubes. During the transfer, transportation and loading and unloading of copper tubes, rain should be avoided; In summer, the ambient temperature of copper pipe is high, and the speed of copper pipe surface is accelerated. When storing copper pipe, pay attention to the principle of first in first out to reduce no loss; The copper pipe loading process is better carried out indoors to avoid the copper pipe being exposed to the sun, at least two layers of canvas shall be used to tightly wrap the whole vehicle materials; After loading, if the truck can not depart in time, the truck shall be driven to the back of the sun to prevent the goods from being exposed to the sun for a long time to absorb heat.However, it is difficult to change this situation too much in the short term. It is expected that the domestic strip steel price will mainly rise in the short term. It is reported that in order to pursue profits, Tangshan Iron and Steel Group Co., Ltd. is currently increasing the supply of hot coils. It does not rule out that more steel mills in the future are inclined to one end of the plate in pursuit of profits, or to lay hidden dangers for the decline. As far as tomorrow is concerned, the price may still maintain a narrow range of shock operation pattern.Yichin,Let s elaborate on the advantages of copper pipe materials: copper pipe floor heating refers to a heating method that uses hot water as the thermal medium, circulates in the copper pipe heating pipe, heats the floor, and heats the floor through the ground in the form of radiation and convection heat transfer. I. The copper tube has fast heat dissipation effect and strong heat resistance. Even under the condition of high temperature water supply, the service life of the floor heating tube will not be affected. Two. Copper pipe is a metal pipe,o it is not easy to scratch. Therefore, it is not easy to leak. Three. High temperature resistance, high pressure resistance, relative to any ordinary plastic pipe. Copper tube floor is warm and resistant to high temperature and pressure. Four. Long service life. Five.Save materials and total cost, stability and performance,Weige40Mn2 alloy steel plate, and can save maintenance.[] Welding process of copper pipe Clean the end and seven ports of steel pipe with steel wool. Do not use abrasive cloth or abrasive paper to clean, because it will affect the clean interface and result in poor welding effect.

The application of copper tube The copper tube is generally used in the heat exchange equipment, and the low-temperature pipeline in the oxygen production equipment can also be used. Some relatively thin copper tubes can be used to transport some pressurized liquids, and can also be used as pressure measuring tubes in instruments; In addition, the copper pipe is relatively firm, unlike other metals, so now many water pipes and refrigeration pipes used in buildings will choose to use the copper pipe.When stacking, reasonable stacking and first in first out shall be achieved.Hygiene and health: various modifiers,WeigeHollow aluminum pipe, additives, additives and other chemical components of plastic pipes in copper pipes.how muchThe room temperature tensile strength of the annealed red copper sheet is ~ kgf/mm, the elongation is ~%, which makes it a suitable choice for modern contractors to install water pipes, heating and cooling pipes in all residential commercial housing.

In Jiangyin market another distribution center, the overall inventory of the current circulation link is about tons, slightly lower than the normal level. At the beginning of this week, the price gap between Jiangyin prices and those in the north has also been able to correspond to the slightly lower circulation inventory. However, from the perspective of the policy port of the steel plant,WeigeGCR15 alloy round steel, the overall production situation of Nangang, Hengrun, Dada, etc. is relatively normal, and the amount of resources in the later period remains stable. The overall inventory of Lecong market remains at about to tons, which is a medium normal level, and the recent spot price of Lecong market has a large gap with that of the north.OK or not?,With the advent of heating season, the raw material support of red copper row is weak. Under the influence of heating season and environmental protection production restriction steel mills in some regions began to implement the production restriction measures for blast furnaces in heating season, the production restriction policy was issued in Tangshan today. From : on October to : on October , the production restriction measures specified in this Notice were implemented.If the environment is wet, it will aggravate the corrosion of copper pipes. Oxygen in water causes corrosion.Overview of three production methods of copper tube Copper tube is a very important material for copper materials. There are many ways to complete the production of this copper tube. For copper pipes, the following three methods are generally used to produce materials. The copper tubes produced by these three methods are not only very good in performance, but also very convenient to operate. There are three production methods for copper tube so what are the three production methods for copper tube?Weige,Four of the five major application fields of copper plate, copper bar and copper pipe: copper is used as various pipes, pipe fittings and decorative devices in the construction industry.If you want to avoid this kind of situation for a long time, you can choose passivation treatment. In this way, not only is the copper surface serious, it can be cleaned under normal circumstances, so this effect is very good.Disadvantages of copper pipe As far as copper pipe is concerned, high production cost and high price are its biggest disadvantages. Compared with other pipe fittings, the cost of copper pipe is much higher, and the connection at the copper pipe interface requires high construction technology level.