The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performanceNaukalpan,　　 The failure to start the water pump may be caused by the power supply or the failure of the water pump itself.　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.ASU　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump　　Is called cavitation phenomenon.　　Stop, then tighten the bearing seat, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose

　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.　　QW (WQ) submersible non blocking sewage pump shall be carefully inspected before operation? Whether the cable is damaged,NaukalpanZD slurry pump, whether the fastener is loose or dropped and whether the pump is deformed or damaged during transportation, storage and equipment.　　Rate loss, so shaft power = effective power + lost power.equipment maintenance ,　　After meters, the sealing of the equipment can not bear the water pressure at this depth.　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.　　 When stopping the operation of the submersible slurry pump, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body

　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipmentDesign brand,　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the operating lift shall not be less than % of the rated lift), which shall be controlled within the recommended operating lift plan as far as possible to prevent the electric pump from burning out the motor due to overload. Pumps without self circulating cooling equipment prevent all of them from being exposed to the water for a long time　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller),NaukalpanSmall deep well pump, magnetic dial indicator, outside micrometer, caliper, feeler gauge, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.Naukalpan　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.