and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified, Seamless pipe is resistant to corrosion, acid, alkali, salt and atmospheric environment, high temperature, impact and fatigue, does not need regular maintenance, and the effective life is more than years; Hot hole breaking cold rolling method. This method is dominated by expansion and expands vertical sliding and skew rolling. The former one is mainly cold rolling by relatively limited mandrel mill, cold rolling by few station mandrel mill, cold rolling by three high limited mandrel mill and cold rolling by fluctuating mandrel mill. In this way, the advantages of high efficiency, low metal material consumption, excellent product quality and excellent automatic control system are more and more widely used. The competitive advantage of the latter one is low cost and short whole process. It is suitable for the processing and manufacturing of CrMoG alloy pipes with large quantities, small types, multi specifications and high precision. Therefore,Carburizing: carburizing is the process of penetrating carbon atoms into the surface layer of steel. It also makes the low-carbon steel workpiece have the surface layer of high-carbon steel, and then after quenching and low-temperature tempering, the part of the workpiece can maintain the toughness and plasticity of low-carbon steel.Stages needing attention in the production and manufacture of alloy tubesAll the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.

I-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.There are many types of galvanized pipes mainly including cold plated seamless pipes and hot-plated seamless pipes. But now the previous one is no longer used. The hot-dip seamless tube is still in use. Hot dip galvanized pipe is mainly used for steel pipes with low pressure fluid such as water and gas. When in use, if in normal working environment, the thickness of galvanized layer of hot-dip galvanized seamless steel pipe is up to μ M above, and it has been used safely for about years. It can be seen that its service life is very long. Of course, when purchasing, we should also find regular manufacturers to order. Only in this way can we achieve this service life. As long as the galvanized pipe is cleaned after pickling, it is basically cleaned in ammonium chloride or zinc chloride aqueous solution or ammonium chloride and zinc chloride mixed aqueous solution tank. In order to ensure the quality, electro galvanizing will not be used. There are also some small enterprises in the market. They will use electro galvanizing in production. In this way, although it is much cheaper in price. However, the quality is very good when used, and it is also easy to have problems.The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, sodium cyanide, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Welcome calls ,Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process it will eventually lead to bad harm to the product quality.→ compared with the concrete structure, the I-steel structure can increase the service area by %, the process of pickling and passivation will be carried out for alloy pipes and reduce the structural design internal force.Generally, but the alloy pipes after pickling and passivation are very easy to rust. Therefore, the way to find a solution to wiredrawing corrosion is 'grinding and polishing'. Due to grinding and polishing, there is no harm to carry out hot galvanizing in the middle and later stage.

Alloy tube is widely used in our daily life, which provides us with great assistance.Standard requirements,After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment put them into the aqueous solution with zinc salt after pickling and passivation,Andorra la Vella How much is 12 I-beam per ton, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage,Andorra la Vella How much is a ton of I-beam now, a layer of zinc is deposited in the pipe. When the end span plate is connected with the concrete beam for structural reinforcement, the length of the surface mesh reinforcement extending into the beam shall not be less than d. When the beam width is small, the extended reinforcement shall be bent . When the perimeter of the floor is poured integrally with the concrete beam or wall, the length of the surface mesh reinforcement extending into the beam shall not be less than the anchorage length of the small reinforcement required by the standard (without transverse reinforcement), when the beam width is small, the extended reinforcement shall be bent.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.Andorra la Vella , Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.Xhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature.Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %