SanheInstallation of small refrigeratorStatus of motion fault diagnosis2022-05-12 00:50:58
Watertight polyurethane rigid foam has low water absorption,SanheInstallation cost of fresh-keeping cold storage, good permeability to water vapor, and state of foam pores. It is not connected with each other,SanheFruit and vegetable fresh-keeping cold storage installation company, and the obturator rate is more than %. It is a dense microporous foam material, which is more dense than the surface of the air, and is not easy to permeate. It is an hydrophobic material.It is required to set up a special tally room (area), and the temperature of the tally area is usually controlled at ~ + ℃.Sanhe,The fresh-keeping storehouse is a device that combines a refrigerator with facilities that use cooling capacity. The design and construction of refrigeration devices is to effectively use cold energy to refrigerate food or other items; This time, the specific reasons for abnormal exhaust temperature in the fresh-keeping warehouse are introduced.The selection of cold storage is very important for cold storage, because cold storage is different from ordinary cold storage. The temperature in cold storage is usually low and the air temperature, humidity and environmental requirements are relatively high. When selecting cold storage, attention must be paid to the selection of cold storage with better temperature. If the selection of cold storage is not good, the temperature in the cold storage is difficult to, which is easy to cause the deterioration of products in the cold storage, or the refrigeration compressor in the cold storage often works,During the cold storage commissioning, special personnel shall be assigned to ensure that the surface of the cold storage plate shall reflect evenly without condensation and cold running; Sealing conditions of joints and holes; Whether the warehouse door and delivery port are not tightly sealed, and timely deal with the problems of insulation and seal failure such as degumming and air leakage.The spacing of pull rivets at inner and outer corners is mm and mm respectively; After the polystyrene library is installed, the wall panel joints shall be evenly sealed and decorated with silicone sealant.The refrigeration equipment in the fresh-keeping environment of the quick-frozen warehouse mostly adopts the single-stage compression refrigeration system, with freon as the refrigerant. The evaporation mode in the warehouse is the cooling fan, which can be ceiling type. If the number of warehouses is small and the volume does not exceed cubic meters the refrigeration mode of the warehouse machine can be considered. If there are a large number of warehouses, the mode of multiple heads in parallel can be considered.
Simple refrigeration is based on the volatilization of refrigerant in the condenser of the cold storage, so as to cool the refrigerant, and then input the refrigerant into the box or building of the refrigeration equipment to cool the air according to the heat exchanger. This kind of refrigeration has slow cooling speed, large total heat conduction temperature difference and complex system software, so it can only be used in less places,SanheInstallation price of large cold storage, such as brine ice making and cold storage with constant temperature requirements.The function of refrigeration is & amp; amp; ldquo； Low temperature storage & amp; amp; rdquo； Introduction & amp; amp; ldquo； Loop type & amp; amp; ldquo； Cold chain logistics & amp; amp; rdquo；The combined cold storage does not cool or the cooling effect is poor. Check whether the condenser of the refrigerator is dirty. Whether frost is too thick on the evaporator in the warehouse. Check whether the refrigerant is leaking (apply soapy water to the pipeline connection, and if bubbles are generated, and reassemble the cold storage door for installation. Check whether the cooler in the cold storage fails and replace it. Whether there is enough clearance for stacking articles in the warehouse and dredge them.How much does it cost?,The selection of equipment for the construction of equipment cold storage is closely related to the size, type and budget of the cold storage.At ordinary times, users should check the sealing degree of the gap of the cold storage, and notify the cold storage for maintenance in time if damaged parts are found.Application of parallel compressor in cold storage: the requirement of refrigeration capacity is large, and to refrigeration compressors under Malige need to be used on weekdays; Long term operation, large load peak valley difference and significant departmental load; Frozen and refrigerated objects are novel foods that are easy to decay and degenerate and have strict requirements for temperature and humidity.
Cold storage has strong stability. Polyurethane foam technology makes it have superior bonding performance. The firm combination of polyurethane rigid foam and carrier layer is the basic premise to ensure the stability of external insulation layer. That is, under the unfavorable local temperature and humidity conditions, the characteristics of the cold storage still do not separate and fall off from the carrier layer and remain stable under normal conditions.quality standard,The exhaust temperature of the compressor equipment is often. When the season changes and the temperature difference changes greatly, pay attention to it. If the machine is abnormal, it needs to be checked in time.The selection of thermal insulation material is important to the quality of controlled atmosphere storage; The selection of thermal insulation materials for the controlled atmosphere storage must be adjusted to local conditions, which should not only have good thermal insulation performance, but also be economical and practical. The thermal insulation materials are divided into several types. One is the plate processed into fixed shape and specification, with fixed length, width and thickness. The plate of corresponding specification can be selected according to the installation needs of the controlled atmosphere storage. The cm thick plate is generally selected for the medium temperature controlled atmosphere storage, cm or cm thick plates are generally selected for low-temperature controlled atmosphere storage and frozen controlled atmosphere storage. The other can be sprayed with polyurethane for foaming, and the materials can be directly sprayed into the built brick or concrete warehouse. After setting, it is moisture-proof and heat-insulating. The heat-insulating material plates include polyurethane, polyphenylene grease, installation, construction, fruit preservation and medical cold storage. Welcome to consult. But the cost is low; Polyphenylene resin has strong water absorption and poor thermal insulation, but the cost is low. The structure of modern controlled atmosphere storage is developing towards assembly, and the storage components including moisture-proof layer and thermal insulation layer are made to achieve on-site assembly. The point is that the construction is convenient, fast and movable, but the cost is relatively high.More and more people begin to build cold storage, and most people choose to use cold storage for cold storage construction. Why? Why do people choose cold storage for construction? What are the advantages of cold storage? The following is a detailed introduction.Sanhe,Cold storage has strong stability. Polyurethane foam technology makes it have superior bonding performance. The firm combination of polyurethane rigid foam and carrier layer is the basic premise to ensure the stability of external insulation layer. That is, the characteristics of the cold storage still do not separate and fall off from the carrier layer and remain stable under normal conditions.The average service life of rigid polyurethane insulation structure with stable quality, long service life and high comprehensive cost performance can reach more than years under normal use and maintenance conditions. Under the normal service conditions during the service life of the structure, it will not be affected by drying, or electrochemical corrosion, as well as the growth of insects fungi or algae or rodents.The product shade warehouse is a warehouse location below ℃ and the sun cannot be straight. The humidity is % ~ % relative humidity, and there are corresponding strict requirements for the wall, ceiling, ventilation, disinfection and epidemic prevention of the warehouse. The refrigeration system adopts full-automatic microcomputer electrical technology and does not need to be on duty. It mainly stores western and Chinese grass materials and instruments, and can monitor and record the temperature and humidity in the storage area.