Several kinds of stainless steel backing welding used for stainless steel backing welding usually adopt TIG process. According to the actual situation of the site, professional L stainless steel pipe, s stainless steel pipe, L stainless steel pipe and other special products, old brands, with advantages in price and guaranteed quality. We can use the following four kinds of backing welding.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Lezhe,The national standard thickness of stainless steel pipe mainly depends on the thickness of raw materials and processing technology. The thickness of welded pipe is basically the same as that of raw materials. For seamless pipe, it is slightly thinner than that of raw materials. At present, the stainless steel pipe industry is dominated by large negative difference, thickness. It provides all kinds of stainless steel plates, stainless steel coils, stainless steel belts, stainless steel pipes for individuals and enterprises all over the country for a long time, on-site settlement and honest operation. There are offices all over the country for long-term cooperation. Generally, there will be . ~ .Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and , martensitic stainless steel is marked with and C,Stainless steel is usually divided into stainless steel pipe, stainless steel pipe and ferritic stainless steel according to the matrix structure. Chromium content % ~ %. Its corrosion resistance, toughness and weldability increase with the increase of chromium content, and its chloride stress corrosion resistance is better than other kinds of stainless steel. Series & mdash; Martensitic precipitation hardening stainless steel.The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas,Lezhe304 manufacturer's stainless steel pipe, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).

Several kinds of stainless steel backing welding used for stainless steel backing welding usually adopt TIG process. According to the actual situation of the site, professional L stainless steel pipe, s stainless steel pipe, L stainless steel pipe and other special products, old brands, with advantages in price and guaranteed quality. We can use the following four kinds of backing welding.According to rolling, it is divided into hot rolled, hot drawn and cold drawn (rolled) stainless steel pipes.Stainless steel pipe, is a new family emerging in the field of pipe materials. It has been widely used in building water supply and direct drinking water pipelines.packing,Continuous casting shall be adopted for stainless steel pipe fittings so as to improve the comprehensive yield, and cooperate with out of furnace refining, which significantly improves the production efficiency, omits the blank opening process and saves a lot of energy consumption.Stainless steel pipe is a kind of economical section steel and an important product in the iron and steel industry. It can be widely used in life decoration and industry. Many people on the market are used to make stair handrails, window guards, railings, furniture,LezheStainless steel pipe cleaning, etc. and materials are common. Series & mdash; martensitic precipitation hardening stainless steel pipe.

Stainless steel has been used as a structural material for building new buildings and repairing historic sites for more than years. Early designs were calculated according to basic principles. Today design codes, such as ANSI as of the American Society of civil engineers, are usedoriginal,Water preparation, purification transportation, regeneration,LezheStainless steel strip factory, seawater desalination and other water industry excellent materials. The demand is about tons.Basic weight (density) / kg of steel plate: SPCC & mdash& mdash; Cold rolled carbon steel sheet and strip are generally used which is equivalent to qa. The third letter C is the abbreviation of cold. When it is necessary to ensure the tensile test, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.Lezhe,When improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, Nb LC) and susl have been applied to frozen shells. Ferritic stainless steel has body centered cubic structure. When the material properties become weaker, sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.Stainless steel is usually divided into stainless steel pipe, stainless steel pipe and ferritic stainless steel according to the matrix structure. Chromium content % ~ %. Its corrosion resistance, toughness and weldability increase with the increase of chromium content, and its chloride stress corrosion resistance is better than other kinds of stainless steel.Model & mdash; High strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).