Model & mdash; The corrosion resistance is the same, and the strength is better because the carbon content is relatively high.Model & mdash; General model; stainless steel. The GB brand is CrNi.Matiguas,If packing is not required, it shall be indicated in the contract and will not bear the problem of scratching and scratching the surface of stainless steel pipe due to opening the packing bag.The recrystallization temperature changes with the shape variable. When the shape variable is %, the recrystallization temperature drops to ℃, and the recrystallization annealing temperature of cold deformed austenitic stainless steel is ~ ℃. At ℃ it needs to be kept warm for h, fully burned at ℃ and then water-cooled.Salamanca,The selection of pipes and fittings for welding data preparation shall be based on the quality elements of the application environment, chemical composition and application pressure, and the commodities of corresponding grades shall be selected to ensure the weld metal structure and machine function.Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.Model & mdash; Cheap model (British and American), usually used as automobile exhaust pipe, is ferritic stainless steel (chromium steel).

Bidirectional Product Description: the tensile strength of the material is ~ mpa, and the high working temperature can reach ℃.Before connecting the pipe fittings mark the depth on the pipe first, so as to prevent it from being inserted in place and stuck. Series & mdash; Heat resistant chromium alloy steel.Honesty and mutual benefit, such as CrMnTi simn,Matiguas316 cold rolled stainless steel plate, (C content is expressed in ten thousandths).After molten steel casting, stainless steel pipe fittings generally adopt the same vertical, vertical bending or arc continuous caster as carbon steel. The refined molten steel is poured into the ladle, the ladle to be poured is transferred above the tundish mouth through the rotary table, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming, condensation and continuous downward movement.Therefore, the field with high utilization rate of stainless steel with high competitiveness and comprehensive quality will also be an important part of the plan.

The bearing capacity of decorative stainless steel pipe ice load is the main control load of offshore platform in severe cold area, which has high requirements for the shear bearing capacity of jacket leg of offshore platform. In order to study the factors affecting the shear capacity of the jacket legs of the stainless steel pipe in pipe concrete-filled steel tubular offshore platform, a total of concrete-filled steel tubular shear members were fabricated to study the effects of outer steel pipe material, void ratio and shear span ratio on the shear capacity of concrete-filled steel tubular in pipe. It is found that the shear strength of members increases with the decrease of void ratio and the increase of concrete strength; The larger the shear span ratio, the empirical formula of shear capacity of concrete-filled steel tubular in pipe is proposed, which is analyzed and verified by ABAQUS finite element modeling software. The results show that the simulation is in good agreement with the test results. In order to study the axial compression performance of stainless steel tube concrete conduit leg and the axial compression performance of stainless steel concrete conduit leg, experiments are used to verify the correctness of the finite element model. The load displacement curves of specimens in groups were compared, and the effects of different void ratio, concrete strength diameter thickness ratio and bone index on the axial compression performance of concrete-filled stainless steel tubular short columns under axial compression were analyzed. The results show that with the increase of concrete strength, the bearing capacity of specimens increases, but the ductility of specimens decreases; With the increase of void ratio and diameter thickness ratio, the bearing capacity of the specimen decreases; The bearing capacity of stainless steel tube concrete can be effectively improved by adding steel bone; Increasing the bone matching index of steel bone can improve the bearing capacity of the specimen. A compound forming process of double-layer stainless steel pipe for primary circuit main pipeline of station is designed, which solves the problem of limited length of finished products in traditional forging or casting process, and meets the special requirements of complex working environment on pipeline performance. The three roll cross rolling forming process of double-layer casing with outer layer -n austenitic heat-resistant stainless steel and inner layer cr-ni martensitic heat-resistant stainless steel was simulated and optimized by using DEFORM-D finite element simulation software. The internal and external deformation, stress-strain field and temperature field of double-layer stainless steel pipe were analyzed, and the optimal deformation parameter combination was obtained by orthogonal test. The simulation results show that in the process of three roll cross rolling, the large values of equivalent stress, equivalent strain and temperature are concentrated in the area between the outer tube and the roll, and the overall performance parameters of the outer tube are greater than those of the inner tube. The range analysis and variance analysis of orthogonal design test show that the optimal deformation parameter is rough rolling temperature deg; C. Feed angle & deg;, Roll speed: rmin. Objective to improve the existing connection mode of the braking system pipe system of railway freight cars, and accurately shape the end of the stainless steel pipe, so as to obtain the forged joint with better mechanical properties. According to the connection mode of the original pipe system and the plastic forming characteristics of steel pipe, a multi-step upsetting and extrusion process for the end of stainless steel pipe is proposed. The process is numerically simulated by DEFORM-D three-dimensional finite element simulation software, and the forging forming process is analyzedManagement Department,At the same time, the Ministry of construction attaches great importance to the application of stainless steel pipes. The industry standard of stainless steel water pipe was issued and implemented in . The Ministry of construction has issued documents on relevant technical specifications and installation sets of pipeline engineering, which are being prepared by Tongji University. All kinds of stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe are qualified. Welcome to telephone inquiry and sincerely invite cooperation! At present, there are stainless steel pipes in Sichuan,MatiguasWeight of stainless steel pipe, Guangdong,Matiguas904L plate stainless steel, Jiangsu and other places, and the products have become mature. Therefore, the time for application has come.The corrosion resistance of corrosion-resistant stainless steel plate mainly depends on its alloy composition (chromium, nickel, silicon, aluminum, manganese, etc.) And internal structure, which mainly acts on chromium. Chromium has high chemical stability, can form a passive film on the steel surface isolate the metal from the outside, protect the steel plate from oxidation and increase the corrosion resistance of the steel plate. After the passive film, the corrosion resistance decreases.When water-soluble paper is used to block the ventilation, due to the ventilation from the weld center, the ventilation pipe shall be pulled out quickly at the later sealing link, and the residual argon inside shall be used for protection, so as to quickly finish the bottom and seal the mouth.Matiguas,The experimental ice load of concrete decorated stainless steel pipe is the highest in the cold areaStainless steel grade group Series & mdash; Chromium nickel manganese austenitic stainless steel series & mdash; Chromium nickel austenitic stainless steel model & mdash; Good ductility, used for molding products. It can also be machined to harden rapidly. Good weldability. The wear resistance and fatigue strength are better than those of stainless steel.Water preparation, storage, transportation, purification, regeneration, seawater desalination and other water industry excellent materials. The demand is about tons.