Rate loss, so shaft power = effective power + lost power.　　 If the impeller of the pump is damaged after a long time of use,BayamoDeep well pump, it will also lead to insufficient liquid supply for the pump.Bayamo,　　 Assembly of water pump: fix the shaft and water inlet joint on the mounting base, fix the impeller and conical sleeve on the shaft with the disassembly cylinder, and then install the guide housing and impeller In this way,　　When using the sand pump which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.Nove Mesto nad Vahom, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation which can be brought wherever it is needed,BayamoQuotation slurry pump, because it does not need too many auxiliary facilities.

　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press the　　Operation management of screw pump Nemo pump (single screw pump) is a positive displacement pump, which is widely used in sewage plant to transport sludge and chemicals containing solid particles.　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also beProfessional is king,　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　A large amount of lubricating oil is stored.　　 Assembly of rotor parts of submersible slurry pump Before assembly apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.

　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated,　　Whether it is the pre installation inspection or the post installation commissioning inspection,BayamoSubmersible slurry pump, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.　　What faults will the water pump control cabinet often encounter in use? The water pump cannot work: cause: a. the power supply is not connected or the output phase of the control cabinet is missing; b. The water pump has been burnt out, and the water pump can not supply water: cause: A. whether there is water in the pool; b. Whether there is gas in the pump body that is not discharged; c. Inlet and outlet water　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.Bayamo,　　About %), in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use